IMG STAGELINE ODC-100/CTW Mode D'emploi page 11

sponding terminating plug (e. g. DLT-123 from
"img Stage Line") to the DMX output jack.
The easiest way to terminate the DMX out-
put of the ODC-100/CTW is to separate an ex-
tension cable ODP-34DMX and to connect the
resistor to the pins 2 and 3 of the plug. Con-
nect the plug with the resistor to the inline jack
of the cable DMX OUT. If no terminating re-
sistor is required, screw the protective cover
provided onto the inline jack of the cable.
4.3.2 Setting the start address
For separate control of all DMX units connected
to the light controller, each unit must have its
own start address. Example: If the first DMX
channel of the spotlight is to be controlled by the
light controller via DMX address 17, set the start
address on the spotlight to 17. All other DMX
channels of the spotlight will be automatically
assigned to the following addresses (i. e. the
addresses 18 – 20 for the start address 17).
1) Press the button MENU repeatedly until the
display shows
2) Press the button ENTER. The display will
show the start address adjusted (
).
3) To set the desired address, press the buttons
UP and DOWN. Now the spotlight can be
operated via the light controller.
Notes
1. If the DMX control does not work, call up the menu
item and press the button ENTER.
appear on the display. If
play, use the button UP or DOWN to switch to
2. When the menu item
on the display and DMX signals are available at
the DMX input, the dot at the right end of the dis-
play will flash.
4.3.3 DMX channels and functions
DMX DMX
channel value
1 000 – 255
2 000 – 255
3 000 – 255 basic brightness warm white
000 – 010
4
011 – 255
‘
DMX overview
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
.
appears on the dis-
, or appears
Function
brightness 0 % © 100 %
basic brightness cool white
stroboscope off
stroboscope slow © fast
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
®
5 Cleaning the Spotlight
Clean the pane in front of the LED at regular
intervals depending on impurities. This is the
only way to ensure that light will be emitted at
maximum brightness. Before cleaning, dis-
connect the mains plug from the socket.
Only use a soft clean cloth and a glass cleaner.
For cleaning the other parts of the housing
of the PARC-100 / CTW, only use a soft clean
cloth. Never use any fluid; it may leak into the
spotlight and damage it.
The weatherproof housing of the ODC-
100 / CTW may also be cleaned with a damp
cloth and a mild detergent.
6 Specifications
Data protocol: . . . . . . . . . . . DMX 512
Number of DMX channels: . 4
Light source: . . . . . . . . . . . COB LED
Power consumption: . . . . 100 W
Beam angle: . . . . . . . . . . 60°
Colour temperature: . . . . adjustable
...
DMX connections: . . . . . . . XLR, 3 poles
Pin assignment: . . . . . . . Pin 1 = ground
Power supply: . . . . . . . . . . 230 V~ / 50 Hz
Power consumption: . . . . . 120 VA max.
must
Protection of housing: . . . . IP 66 (ODC- only)
.
Dimensions w/o
mounting bracket: . . . . . . . ∅ 185 × 250 mm
Weight: . . . . . . . . . . . . . . . . 6.5 kg
Subject to technical modification.
2700 K – 5600 K
Pin 2 = DMX-
Pin 3 = DMX+
11