8. Move the range into its final location. Check that the range
is level by placing a level on the oven bottom. See the "Level
Range" section.
IMPORTANT: If the range is moved to adjust the leveling
legs, verify that the anti-tip bracket is engaged by repeating
steps 1 to 8.
Electronic Ignition System
Initial Lighting and Gas Flame Adjustments
Cooktop and oven burners use electronic igniters in place of
standing pilots. When the cooktop control knob is turned to the
ignite position, the system creates a spark to light the burner. All
cooktop burners will spark, but only the burner with the control
knob turned to the ignite position will produce a flame. This
sparking continues as long as the control knob is turned to the
ignite position.
When the oven control is turned to the desired setting, sparking
occurs and ignites the gas.
Check Operation of Cooktop Burners
Standard Surface Burners
Push in and turn each control knob to the ignite position.
The flame should light within 4 seconds. The first time a burner
is lit, it may take longer than 4 seconds to light because of air in
the gas line.
If Burners Do Not Light Properly:
Turn cooktop control knob to the off position.
■
Check that the range is plugged into a grounded 3 prong
■
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
Check that the gas shut-off valves are set to the open
■
position.
Check that burner caps are properly positioned on burner
■
bases.
Repeat start-up. If a burner does not light at this point, turn
the control knobs to the off position and contact your dealer or
authorized service company for assistance. Please reference the
"Warranty" section of the User Guide to contact service
If the cooktop "low" burner flame needs to be adjusted for any
of the burners, see the "Adjust Flame Height" section.
Check Operation of Oven Bake Burner
1. Press BAKE.
2. Press the Start pad.
The oven burner should light within 8 seconds. The first time
a burner is lit, it may take longer than 8 seconds to light
because of air in the gas line.
3. After 2 minutes, open the oven door and check that the oven
is warm.
If Burner Does Not Light Properly:
Press the Off pad.
■
Check that the range is plugged into a grounded 3 prong
■
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
Check that the gas shut-off valves are set to the open
■
position.
14
Repeat steps 1 to 3. If the burner does not light at this point,
press the off pad and contact your dealer or authorized service
company for assistance. Please reference the "Warranty" section
of the User Guide to contact service
If the bake burner flame needs to be adjusted, see the "Adjust
Flame Height" section.
Refer to the User Guide for proper operation of the oven
controls.
Check Operation of Oven Broil Burner
1. Close the oven door.
2. Press BROIL.
3. Press the Start pad.
The oven burner should light within 8 seconds. The first time
a burner is lit, it may take longer than 8 seconds to light
because of air in the gas line.
4. After 2 minutes, open the oven door and check that the oven
is warm.
If Burner Does Not Light Properly:
Press the Off pad.
■
Check that the range is plugged into a grounded 3 prong
■
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
Check that the gas shut-off valves are set to the open
■
position.
Repeat steps 1 to 3. If the burner does not light at this point,
press the off pad and contact your dealer or authorized service
company for assistance. Please reference the "Warranty" section
of the User Guide to contact service
If the broil burner flame needs to be adjusted, see the "Adjust
Flame Height" section.
Refer to the User Guide for proper operation of the oven
controls.
Remove/Replace Drawer
(on some models)
Remove all items from inside the baking drawer, warming drawer
or premium storage drawer, and then allow the range to cool
completely before attempting to remove the drawer.
To Remove:
1. Open the drawer to its fully open position.
2. Using a flat-blade screwdriver, gently loosen the drawer
from the glide alignment notch, and then lift up the drawer
alignment tab from the glide.
A. Flat-blade screwdriver
B. Drawer alignment tab
C. Drawer glide notch
3. Repeat Step 2 on the other side. The drawer is no longer
attached to the drawer glides. Using both hands, pick up the
drawer to complete the removal.
A
B
C