Adjusting setup items — SET
1
Press and hold the select button.
The setup display appears.
2
Press the select button repeatedly
until the desired item appears.
3
Rotate the control dial to select the
setting (example "ON" or "OFF").
4
Press and hold the select button.
The setup is complete and the display returns
to normal play/reception mode.
Note
Displayed items will differ, depending on the source
and setting.
The following items can be set (follow the page
reference for details):
"
" indicates the default settings.
z
CLOCK-ADJ (Clock Adjust) (page 4)
CT (Clock Time)
To set "CT-ON" or "CT-OFF" (
BEEP
To set "BEEP-ON" (
) or "BEEP-OFF."
z
AUX-A*
1
(AUX Audio)
To turn the AUX source display "AUX-A-ON"
(
) or "AUX-A-OFF" (page 12).
z
A.OFF (Auto Off)
To shut off automatically after a desired time
when the unit is turned off.
– "A.OFF-NO" (
), "A.OFF-30S (Seconds),"
z
"A.OFF-30M (Minutes)" or "A.OFF-60M
(Minutes)."
SUB/REAR*
1
To switch the audio output.
– "SUB-OUT" (
): to output to a subwoofer.
z
– "REAR-OUT": to output to a power amplifier.
DEMO (Demonstration)
To set "DEMO-ON" (
z
DIM (Dimmer)
To change the brightness of the display.
– "DIM-ON": to dim the display.
– "DIM-OFF" (
): to deactivate the dimmer.
z
M.DSPL (Motion Display)
To select the Motion Display mode.
– "M.DSPL-ON" (
): to show moving patterns.
z
– "M.DSPL-OFF": to deactivate the Motion
Display.
A.SCRL (Auto Scroll)
To scroll long displayed item automatically
when the disc/album/track is changed.
– "A.SCRL-ON" (
): to scroll.
z
– "A.SCRL-OFF": to not scroll.
) (page 9, 10).
z
) or "DEMO-OFF."
LOCAL (Local Seek Mode)
– "LOCAL-ON": to only tune into stations with
stronger signals.
– "LOCAL-OFF" (
): to tune normal reception.
z
MONO*
2
(Monaural Mode)
To improve poor FM reception, select monaural
reception mode.
– "MONO-ON" : to hear stereo broadcast in
monaural.
– "MONO-OFF" (
): to hear stereo broadcast in
z
stereo.
REG*
2
(Regional)
To set "REG-ON" (
) or "REG-OFF" (page 9).
z
LPF*
3
(Low Pass Filter)
To select the subwoofer cut-off frequency: "LPF
OFF" (
), "LPF 80Hz," "LPF 100Hz," "LPF
z
120Hz," "LPF 140Hz" or "LPF 160Hz."
LPF NORM/REV*
3
(Low Pass Filter)
To select the phase when the LPF is turned on:
"NORM" (
) or "REV."
z
HPF (High Pass Filter)
To select the front/rear speaker cut-off
frequency: "HPF OFF" (
100Hz," "HPF 120Hz," "HPF 140Hz" or "HPF
160Hz."
LOUD (Loudness)
To allow you to listen clearly at low volume
levels.
– "LOUD-ON": to reinforce bass and treble.
– "LOUD-OFF" (
): to not reinforce bass and
z
treble.
BTM (page 8)
*1 When the unit is turned off.
*2 When FM is received.
*3 When the audio output is set to "SUB."
), "HPF 80Hz," "HPF
z
11