Operating Modes; Starting Operation - stayer CP190B Instructions D'emploi

Mounting the Extraction Adapter / External Dust
Extraction
Attach the extraction adapter onto the sawdust ejector until it latches
(16).
The machine can be plugged directly into the receptacle all-purpose
vacuum cleaner with remote starting control. The vacuum cleaner
starts automatically when the machine is switched on.
The vacuum cleaner must be suitable for the material being worked.
When vacuuming dry dust that is especially detrimental to health or
carcinogenic, use a special vacuum cleaner.
5. Operation

Operating Modes

Before any work on the machine itself, pull the mains plug.
Adjusting the Cutting Depth
l
Adjust the cutting depth to the thickness of the workpiece. Less than a
full tooth of the blade teeth should be visible below the workpiece.
Loosen the clamping lever (25). For a smaller cutting depth, pull the
saw away from the base plate (14); for a larger cutting depth, push the
saw toward the base plate (14). Adjust the desired cutting depth at the
cutting -depth scale.Tighten the clamping lever (25) again.
The tightening tension of the clamping lever (25) can be readjusted.
For this, unscrew the clamping lever (25), and screw it back again
turned offset by at least 30° in anticlockwise direction.
Adjusting the Cutting Angle
l
It is best to place the machine on the face side of the blade guard (1).
Loosen the wing bolts (7) and (15). Tilt the saw sidewards. Adjust the
desired measure on the scale (6). Tighten the wing bolts (7) and (15)
again.
Note: For bevel cuts, the cutting depth is smaller than the setting
indicated on the cuttingdepth scale 26.
Cutting Marks
The 0° cutting mark (10) indicates the position of the saw blade for
right-angled cuts. The 45° cutting mark (9) indicates the position of
the saw blade for 45° cuts.
For precise cuts, position the circular saw against the workpiece as
shown in the figure. It is best to carry out a trial cut.

Starting Operation

Observe correct mains voltage! The voltage of the power source
must agree with the voltage specified on the nameplate of the
machine. Power tools marked with 230 V can also be operated
ENGLISH
12
with 220 V.
Switching On and Off
l
To start the machine, first push the lock-off button for the On/Off switch
(2) and then press the On/Off switch (3) and keep it pressed.
To switch off the machine, release the On/Off switch (3).
Note: For safety reasons, the On/Off switch (3) cannot be locked; it
must remain pressed during the entire operation.
Reduced starting current
l
The electronic reduced starting current limits the power consumption
when switching the tool on and enables operation from a 16 ampere
fuse.
Operating Instructions
Protect saw blades against impact and shock. Guide the machine
evenly and with light feed in the cutting direction. Excessive feed
significantly reduces the service life of the saw blade and can cause
damage to the power tool.
Sawing performance and cutting quality depend essentially on the
condition and the tooth form of the saw blade. Therefore, use only
sharp saw blades that are suited for the material to be worked.
Sawing Wood
l
The correct selection of the saw blade depends on the type and quality
of the wood and whether lengthway or crossway cuts are required.
When cutting spruce lengthways, long spiral chips are formed.
Beech and oak dusts are especially detrimental to health. Therefore,
work only with dust extraction.
Sawing with Parallel Guide
l
The parallel guide 11 enables exact cuts along a workpiece edge and
cutting strips of the same dimension.
Loosen wing bolt 8 and slide the scale of the parallel guide (11)
through the guide in the base plate (14). Adjust the desired cutting
width as the scale setting at the respective cutting mark (10) or (9); see
Section "Cutting Marks". Tighten wing bolt 8 again.
Sawing with Auxiliary Guide
l
For sawing large workpieces or straight edges, a board or strip can
clamped to the workpiece as an auxiliary guide; the base plate of the
circular saw can be guided alongside the auxiliary guide.
Illuminating the Work Area (LED)
l
Provide for sufficient lighting of the direct working area.
– For this, switch on the lighting unit (32) with the switch.
– If required, each lamp can be aligned individually.
Observation: The laser guide and lantern are feeded by two AAA
1.5V batteries. When exhausted, please replace them loosen the
screw (33) for accessing the batteries.
Laser guide
l
The built-in laser guide is intended to obtain a precision cut. Use the
laser guide (14) every time the work requires precision cuts, as when
following pre-drawn lines on a surface.
Set the I/O laser switch (16) to the position I to activate the laser guide
(14).
Press the On/Off switch (2), and start cutting the workpiece following
the predrawn linewith the projected laser line on the surface.
12