EUROM VALENCIA Manuel D'utilisation page 16

Operating using the remote control:
It takes a little time before the receiver responds to a signal transmitted from the remote control. Do not press a
button more frequently than once per two seconds as this will disrupt the function.

You switch the atmospheric lighting on and off using the red ON/OFF button on the remote control.

The black buttons '1000W' and '2000W' have the same function as the '1000W' and '2000W' buttons on the
fireplace (see above).

Pressing and holding the black 'dimmer' button increases and decreases the brightness of the light. Release
the button when the lighting reaches the desired intensity.

Every time you press a button you will hear a 'beep' and this indicates that the fireplace has 'picked up' the
command.

When you switch a particular function on using the remote control, the red light next to the corresponding
button on the fireplace will be illuminated.
Replacing a bulb

Always unplug the fireplace before replacing a bulb!

The bulbs get hot during use; allow plenty of time for them to cool down before touching them!

Two people are required to replace a bulb.

Carefully remove the glass plate in front of the fireplace by lifting it off its hooks. Put it somewhere safe.

We advise you to now take the fireplace off the wall. In order to do so, the two screws which attach the
fireplace to the lower spacer bracket must be removed. Lie the fireplace down on a flat, clean surface.

Under the 'fire' there is a cover place which covers the bulbs. Remove the 6 screws from this cover plate
and remove cover plate.

You must remove the flexible rotator in order to gain access to the bulbs. Pinch the clamp on the right hand
side and move to the left, away from the rubber. Now slide the rubber off the axle (to the left). Once this is
free of the axle, gently pull forwards and slide/pull gently to the right (out of the left hand side attachment
point).

Remove the broken bulb and replace with a 40Watt G9 halogen bulb. Never touch a halogen bulb with bare
hands!

Replace the rotator by following the instructions above in reverse order.

Screw on the cover plate, hang the fireplace on the wall supports and screw in the screws which attach the
fireplace to the spacer bracket. Finally, replace the glass plate on the hooks, in front of the fireplace.
Safety feature
The Valencia atmospheric fireplace is equipped with an overheating safeguard. In case of internal overheating,
the overheating safeguard will switch the heater off. This may occur if the heater cannot give off enough heat or if
it cannot draw in enough fresh air. As mentioned above, this is generally caused by (partially) covering the heater,
obstructing the air intake and/or outlet grills or installing the heater too close to a wall or something similar.
If this happens, turn the fireplace off by switching the main switch to O and remove the plug from the socket.
Leave the fireplace to cool down for at least 15 minutes and remove the cause of overheating. You can then
switch the fireplace back on.
If the device overheats again or you cannot ascertain the reason for this, take the fireplace to your service point to
be checked/repaired.
Cleaning and maintenance
Always remove the plug from the socket and let the fireplace cool down before cleaning or touching.
The Valencia atmospheric fireplace does not need much maintenance. Always keep the in- and outlet openings
clean and dust-free. Use a soft cloth or a soft brush to clean the outside of the metal case. The glass plate can
also be cleaned with a soft cloth. Do not use abrasive cleaning fluids or special glass cleaners!
Apart from the bulbs, the fireplace contains no parts which need to be replaced by the user. If the device
malfunctions, immediately remove the plug from the socket and take to a service point. Do not carry out repairs
yourself and always ask for original parts to be used.
If the fireplace is to be stored after the winter period, clean it, pack it in original packaging if possible and store in
a cool, dry and clean place. Make sure the fireplace is kept upright.
Problems and solutions
If the fireplace will not work check the electrical supply. Is the socket working properly? Has the fuse blown?
If the fireplace stops working suddenly, it may mean that the overheating safeguard has been triggered (see
under 'Safeguards').
If the atmospheric lighting is not working or does not work properly, one or more of the bulbs may need to be
replaced (see 'Replacing a bulb').
16