EUROM VALENCIA Manuel D'utilisation page 14

with physical, sensory or mental disabilities or by anyone who does not have knowledge about or experience
with the device.
22. Keep the fireplace clean. Dust, dirt and/or deposits in the fireplace often lead to overheating. Ensure that this
type of build-up is regularly removed. Do not use aggressive products or metal scourers for cleaning the
device as this will damage the housing and parts of the metal may find their way into the electrical parts and
lead to short circuiting.
23. Never switch the device on if you have noticed damage to the device itself, the cable or plug or if it does not
work properly, has fallen or shows any other signs of failure. Take the entire device back to your supplier or
a recognised electrician to be checked and/or repaired. Always ask for original parts to be used.
24. Do not lift the fireplace using the glass plate.
25. Do not use accessories that have not been supplied or approved by the manufacturer.
26. The bulbs are the only parts of this device that the user may replace themselves. Any other repairs to the
fireplace, cable or plug must always be carried out by qualified personnel. Repairs that have not been
carried out correctly may pose a risk!
27. Only use the fireplace for its intended purpose and as stipulated in this instruction booklet.
Failing to adhere to instructions 25, 26 and 27 could lead to damage, fire and/or personal injury. This will
invalidate the guarantee and the supplier, importer and/or manufacturer will take no responsibility for the
consequences!
Description
The VALENCIA comprises an atmospheric fireplace (containing a heating element and ventilator which blows
warm air out of the top of the fireplace), wall supports, a remote control and this instruction booklet.
The atmospheric fireplace is covered with a rounded glass plate at the front. There is a metal cabinet behind
this which contains the atmospheric elements at the front, air grilles at the sides and, on top, the grille which is
used to blow out warm air and the operating panel. The hanging bracket is located at the back and the technical
aspects are housed internally.
The wall supports must be attached to the wall so that the fireplace can be hung on them. Screws, plugs, a
spacer bracket and self-tapping screws are supplied.
There are four buttons on the remote control; one red and three black. The red button switches the atmospheric
screen on; the two upper black buttons are for setting heat levels (1000 and 2000 Watt respectively) and the
lower black button (the dimmer) is used to regulate the clarity of the screen.
Please keep the instruction booklet somewhere safe for reference or for providing with the device if it is sold on.
Location and Connection

Remove all packaging material and keep out of reach of children. After removing packaging, check the
appliance for damage or other signs that could indicate a fault/defect/malfunction. In case of doubt, do not
use the appliance, but contact your vendor for inspection or replacement.

Do not use the fireplace before it has been completely installed according to the instructions and you have
read the instruction booklet fully!

This device was designed to be permanently hung on a wall. Ensure the wall is sturdy, completely vertical, is
not sensitive to vibration and is not flammable. Make sure it is not made of synthetic material and or covered
with flammable material. Be aware of pipes that may be contained within the walls when drilling holes.

Choose a suitable location for the fireplace, at least one metre from all obstructions, walls and flammable
materials (see safety instructions) and in the vicinity of a 16 Amp (at least) fused, earthed electrical socket
(protected by a 30 mA earth leakage circuit breaker). This socket must be located to the right of the
fireplace.

There must be at least 30 cm distance between the base of the fireplace and the ground, however, you are
advised to place the fireplace at a height of 60 cm. for the best sight. There must be at least 20 cm distance
between the fireplace and the side walls, at least 100 cm. between the fireplace and the ceiling. Do not hang
the device directly under or in front of an electrical socket (see diagram 1).

The wall supports must be attached horizontally (use a spirit level!) to the wall. Determine the location of the
wall supports (take the above into account), mark the location of the screws and drill 5 holes at the marked
places using a 6 mm drill. Put the plugs into the holes and then screw the wall supports to the wall. Be
aware of pipes that may be contained within the walls when drilling holes!

Attach the spacer bracket with both self-tapping screws underneath the fireplace in the holes provided. The
flat side of the bracket must be placed against the underside of the fireplace; the other must rest against the
wall so that the wall piece sticks out under the fireplace (diagram 3). This bracket will be hidden from sight
once the glass screen has been installed.

Now hang the fireplace carefully on the central wall support with the hanging bracket (see diagram 2). The
bracket should not stick out from the support! The electrical cable comes out at the right hand, lower side of
the fireplace and must be placed out of range of the heat.
14