Specifications; Unpacking Your Saw; Familiarization - DeWalt DW713 Guide D'utilisation

Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
Miter Saw Replacement Kerf Plate: DW7055 (not shown)
This durable plastic uncut plate limits blade tear out.
Miter Saw Stands: DWX723, DWX724, DWX725B (not shown)
Provides stable and accurate work platform for miter saws.
FIG. 1
DW7080
LOCKNUTS
END PLATE
SAW BLADES: ALWAYS USE 10" (254 mm) SAW BLADES WITH 5/8" (16 mm) ARBOR
HOLES. SPEED RATING MUST BE AT LEAST 5500 RPM. Never use a smaller diameter
blade. It will not be guarded properly. Use crosscut blades only! Do not use blades designed
for ripping, combination blades or blades with hook angles in excess of 7 degrees.
BLADE DESCRIPTIONS
APPLICATION
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose
Fine Crosscuts
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts
Non-ferrous metals
NOTE: For cutting non-ferrous metals, use only saw blades with
TCG teeth designed for this purpose.
DW7082
DW7084
DIAMETER TEETH
10" (254 mm) 40
10" (254 mm) 60
10" (254 mm) 80
10" (254 mm) 80
Specifi cations
CAPACITY OF CUT
50° miter left and right
48° bevel left: 3° right
0° miter
Max. Height 3.5" (89 mm) Result Width 3.5" (89 mm)
Max. Width 6.1" (155 mm) Result Height 1.25" (32 mm)
45° miter
Max. Height 3.5" (89 mm) Result Width 2.4" (61 mm)
Max. Width 4.2" (107 mm) Result Height 1.25" (32 mm)
45° bevel
Max. Height 2.3" (58 mm) Result Width 3.5" (89 mm)
Max. Width 6.1" (155 mm) Result Height .75" (19 mm)
31.62° miter and 33.85° bevel
Max. Width 5.25" (133 mm) Result Height .9" (23 mm)
DRIVE
120 Volt Motor
2200 Watts 15 Amp Motor
5000 RPM Cut Helical Gears with Roller and Ball Bearings
Carbide Tooth Blade Automatic Electric Brake

Unpacking Your Saw

Check the contents of your miter saw carton to make sure that you have received all parts. In
addition to this instruction manual, the carton should contain:
1. One No. DW713 miter saw with blade.
2. One blade wrench in wrench pocket shown in Figure 2.
3. One No. DW7053 Dust Bag.

Familiarization

Your miter saw is fully assembled in the carton.
Open the box and lift the saw out by the convenient
carrying handle, as shown in Figure 1A.
Place the saw on a smooth, flat surface such as a
workbench or strong table.
Examine Figures 2 and 3 to become familiar with
the saw and its various parts. The section on
adjustments will refer to these terms and you must
know what and where the parts are.
CAUTION: Pinch Hazard. To reduce the risk of
injury, keep thumb underneath the handle when
pulling the handle down. The lower guard will move up as the handle is pulled down which
could cause pinching.The handle is placed close to the guard for special cuts.
Press down lightly on the operating handle and pull out the lock down pin, as shown in
Figure 6. Gently release the downward pressure and allow the arm to rise to its full height. Use
the lock down pin when carrying the saw from one place to another. Always use the carrying
handle to transport the saw or the hand indentations shown in Figure 2 and 3.
4
FIG. 1A