Scheppach DBS800 Mode D'emploi page 12

the risk of electric shock.
• Do not abuse the cord; do not use the cord to carry
or hang up the power tool or to unplug the power
tool from the mains. Keep the power cord away from
heat, oil, sharp edges or the power tool's moving
parts. Damaged or tangled power cords will increase
the risk of electric shock.
• When operating a power tool outdoors, use only
extension cords that are approved for outdoor use.
The use of an extension cord that is adapted for out-
door use reduces the risk of electric shock.
• If working with the power tool in a damp location
cannot be avoided, use a ground fault circuit inter-
rupter. The use of a ground fault circuit interrupter
reduces the risk of electric shock. Always check
whether the mains voltage complies with the voltage
specified on the nameplate of the power tool.
Personal safety
• Stay alert. Watch what you are doing and use com-
mon sense when operating a power tool. Do not use
the power tool while you are tired or under the influ-
ence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
• Use personal protective equipment. Always wear sa-
fety glasses. Safety equipment such as a dust mask,
non-skid safety shoes, a hard hat or ear protection
depending on the type and use of the power tool will
reduce personal injuries.
• Prevent unintentional starting. Ensure that the po-
wer tool is switched off before connecting it to the
power supply and/or battery, picking it up or carrying
the tool. Carrying power tools with your finger on
the switch or energizing power tools that have the
switch on invite accidents.
• Remove any adjusting tool or wrench before turning
the power tool on. A wrench or a key which has be-
en left attached to a rotating part may induce per-
sonal injury. Do not overreach. Keep proper footing
and balance at all times. This enables you to better
control the power tool in situations which cannot be
foreseen.
• Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair
may get caught in moving parts.
• If dust extraction and collection units are installed,
make sure that these are connected and properly
used. Using such devices reduces hazards associa-
ted with dust.
Power tool use and care
• Do not force the power tool. Use the correct power
tool for your application. With the correct power tool
you will do the job better and safer at the specified
power rate.
• Do not use the power tool if it has a defective switch.
A power tool, which cannot be turned on or off with
the switch, is dangerous and must be repaired.
• Unplug the power cord from the outlet and/or re-
move the battery before making any adjustments to
the tool, changing accessories, or storing the power
tool. Such preventive safety measures prevent star-
ting the tool accidentally.
• Store idle power tools out of children's reach. Do not
allow persons unfamiliar with the tool or these inst-
ructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
• Keep the power tools in good condition. Check that
moving parts are functioning smoothly and do not
lock, whether parts are broken or for any other con-
dition that may affect the power tool's operation. If
12 І 64
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
damaged, have the power tool repaired before use.
Many accidents are associated with poorly maintai-
ned power tools.
• Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are like-
ly to block less and are easier to control.
• Use the power tool, the accessories, bits, etc. in ac-
cordance with these instructions and in the manner
intended for the particular type of equipment. Take
into account the working conditions and the work
to be performed. Using power tools for operations
different from those intended can lead to hazardous
situations.
Service
• Have your electric tool repaired only by trained per-
sonnel using only genuine spare parts. This will en-
sure that your electric tool remains safe to use
Further Safety Instructions
• Connect the device only to a power point with a
residual current protective device (RCD) with a
measured residual current of not more than 30 mA.
• Keep the mains cable and extension cable away
from the grinding disk and saw chain. In the event
that it is damaged or severed, immediately discon-
nect the plug from the socket. Do not touch the ca-
ble before it has been disconnected from the mains.
Risk of electric shock.
• The replacement of the plug or the connection line
must always be executed by the manufacturer of the
electric tool or his/her customer service in order to
avoid any hazards.
• Only switch the device on once it is safely fixed to
the worktop.
• For your own safety only use accessories and
attachments which were stated in the operating
instructions or recommended or specified by the tool
manufacturer.
• Only use grinding discs where the printed rotational
speed is at least as high as what has been specified
on the name plate of the device.
• Carry out a visual inspection of the grinding disc
before use. Do not use any damaged or deformed
grinding discs. Replace any damaged or worn grin-
ding discs.
• Make sure that the sparks produced by grinding do
not present a danger, e.g. reach people or ignite
flammable substances.
• Never keep the fingers between the grinding disc
and spark protection or in close proximity to the
protective hoods. There is a risk of crushing.
• The rotating parts of the device cannot be covered
due to functional reasons. Therefore, proceed cauti-
ously and hold the workpiece firmly in order to avoid
slipping which could cause your hands to come into
contact with the grinding belt or grinding disc.
• The workpiece gets hot during grinding. Do not
touch the machined area, allow it to cool down.
There is a risk of burning. Do not use coolants or the
like.
• If you are tired or have consumed alcohol or tablets,
do not work with the device. Always have a break on
time.
• Switch the device off and remove the mains plug
- to loosen a blocked insertion tool,
- if the connection line is damaged or entangled,
- in case of unusual sounds.