Instructions; Placement; Insert For The Warming Plate/Cup Shelf (13); Push Buttons (8/9) - BOMANN ES 184 CB Mode D'emploi

Instructions

Placement

• Place the appliance on a stable and level surface.
• Due to rising heat and vapours do not operate the appli-
ance under wall cabinets.
• Do not place the appliance in close proximity to a gas or
electric stove or any other heat source.

Insert for the warming plate/cup shelf (13)

Place the insert in the notch at the top of the appliance.

Push Buttons (8/9)

These push buttons have the following functions when locked
in place or disengaged:
Switch Engaged
8
(Pump)
9 (Steam)

Electric Connection

1. Ensure that your mains power corresponds with the specifi-
cations of the appliance. The specifications are printed on
the type label.
2. Check the push button settings! Push buttons (8/9) must
be disengaged.
3. Connect the mains cable to a properly installed and earthed
wall outlet.
On / Off
• Press the on / off button (12) briefly to switch the appliance
on. The appliance starts heating up. The warming plate (13)
heats up.
• The Indicator lamp lights up as soon as the necessary
brewing temperature is reached.
NOTE:
The indicator lamp turns on and off during operation.
This is normal and indicates that the temperature is
thermostat-controlled and maintained.
• In order to switch the appliance off, press and hold the on /
off button (12) for 4 seconds. Then disconnect the mains
plug from the socket.

European regulations on energy saving

NOTE:
The European Directive 2009/125/EC (Ecodesign Directive)
incorporates measurements for energy saving.
The following applies to coffee makers: The keep-warm
period is limited to max. 40 minutes after which the appliance
turns off automatically.
You benefit from better safety and lower energy consumption.
Disengaged
(Standby)
(Espresso)

Operation

WARNING: Important!
Before use, always check the button settings! The buttons
(8/9) must be in the off position, before connecting the appli-
ance to a properly installed earthed socket!

Attach / Detach Filter Holder

• Hold the handle at the left edge of the appliance to attach
the filter holder (see Fig. B on page 3). Insert the three
guide tabs in the group head recesses. With the handle pull
the filter holder to the right hand side to the middle of the
appliance. Ensure that the filter holder is well secured in
the group head.
• Pull the filter holder to the left to detach from the group
head.
WARNING: Danger of burns!
After brewing the metal parts of filter holder and filter
insert are hot.

Inserting the drip tray / drip tray grid

• Slide the drip tray for the residual water (6) into the com-
partment (5).
• Place the drip tray grid (7) onto the compartment as a
cover. The recessed edge must face the appliance hous-
ing.

First Use / Bleeding

CAUTION:
Bleed the appliance before first use and after a longer period
of non-use. Do not use coffee grounds during this process!
1. Make sure that the drip tray (6) and the drip tray grid (7) are
inserted.
2. Fill the water tank with clean, fresh water to the MAX mark-
ing. Close the lid again.
3. Remove the filter holder (16) from the group head.
4. Press the on / off button (12) briefly to switch the appliance
on. The status indicator lamp (11) lights up. The appliance
starts heating up. The warming plate (13) heats up.
5. Swivel out the steam nozzle (4). Ensure that the steam
pipe is properly attached.
6. Place a suitable container (heat-resistant / approx. 500 ml)
under the steam nozzle.
7. Turn the steam control knob (3) all the way towards " ".
8. Press push button (8) to turn on the pump. Pumping starts.
9. Turn off the pump after water is evenly emitted from the
steam nozzle. Push button (8) is in
10. Close the steam control knob towards " ".
11. Empty the container and place it under the group head.
12. Press push button (8) to turn on the pump. The water flow
starts. Let all water from the water tank run through. Turn
off the pump to empty the container.
position.
53