Dremel 8100 Notice Originale page 22

If the green indicator light is "ON", the battery pack cannot accept
a charge.
GENERAL
The Dremel multitool is a high quality precision tool that can be
used to perform detailed and intricate tasks. The wide range of
Dremel accessories and attachments allow you to perform a large
variety of tasks. These include tasks such as sanding, carving,
engraving, routing, cleaning and polishing.
PICTURE 1
A. Shaft lock button
B. On/Off and variable speed slide switch
C. Battery pack
D. Battery release tabs
E. Ventilation openings
F. Housing
G. Battery pack
H. Battery release tabs
I. Shaft
J. EZ Twist™ integrated wrench/nose cap
K. Collet nut
L. Collet
M. Wrench
COLLETS
The Dremel accessories available for the multitool come
with various shank sizes. Four size collets are available to
accommodate the different shank sizes. Collet sizes are identified
by the rings on the back of the collet.
PICTURE 4
A. Collet nut
B. 3.2 mm Collet without ring (480)
C. 2.4 mm Collet with three rings (481)
D. 1.6 mm Collet with two rings (482)
E. 0.8 mm Collet with one ring (483)
F. Indentification rings
NOTE: Some multitool kits may not include all four collet sizes.
Collets are available separately.
Always use the collet that matches the shank size of the
accessory you plan to use. Do not force a larger diameter shank
into a smaller collet.
CHANGING COLLETS
PICTURE 5
A. Wrench
B. Shaft lock button
C. Collet nut
D. To loosen
E. To tighten
1. Press the shaft lock button, hold down and rotate the shaft by
hand until it engages the shaft lock. Do not engage the shaft
lock button while multitool is running.
2. With the shaft lock button engaged, loosen and remove the
collet nut. Use the collet wrench if necessary.
3. Remove the collet by pulling it free from the shaft.
4. Install the appropriate size collet fully into the shaft and
reinstall the collet nut finger tight. Do not fully tighten the nut
when there is no bit or accessory installed.
CHANGING ACCESSORIES
1. Press the shaft lock button and rotate the shaft by hand until
it engages the shaft lock. Do not engage the shaft lock button
while multitool is running.
2. With the shaft lock button engaged, loosen (do not remove)
the collet nut. Use the collet wrench if necessary.
3. Insert the bit or accessory shank fully into the collet.
4. With the shaft lock button engaged, finger tighten the collet
nut until the bit or accessory shank is gripped by the collet.
NOTE: Be sure to read the instructions supplied with your Dremel
accessory for further information on its use.
Use only Dremel tested, high performance accessories.
EZ TWIST™ INTEGRATED WRENCH/NOSE CAP
PICTURE 6
A. EZ Twist™ integrated wrench/nose cap
B. Shaft lock button
C. Collet nut
D. To loosen
E. To tighten
The nose cap of your tool has an integrated wrench allowing
you to loosen and tighten the collet nut without the use of the
standard collet wrench.
1. Unscrew the nose cap from the tool, line-up the steel insert
on inside of the cap with the collet nut.
2. With the shaft lock engaged twist nose cap counter clockwise
to loosen the collet nut. Do not engage the shaft lock button
while multitool is running.
3. Insert the bit or accessory shank fully into the collet.
4. With the shaft lock engaged twist nose cap clockwise to
tighten the collet nut.
5. Screw the nose cap back into its original position.
NOTE: Be sure to read the instructions supplied with your
Dremel accessory for further information on its use.
Use only Dremel tested, high performance accessories.
BALANCING ACCESSORIES
For precision work, it is important that all accessories be in good
balance (much the same as the tires on your automobile). To true
up or balance an accessory, slightly loosen collet nut and give
the accessory or collet a 1/4 turn. Re tighten collet nut and run
the Rotary Tool. You should be able to tell by the sound and feel
if your accessory is running in balance. Continue adjusting in this
fashion until best balance is achieved.
22