Dremel 8100 Notice Originale page 21

with the guard. Wire wheel or brush may expand in diameter
due to work load and centrifugal forces.
c. Do not exceed 15000 min–1 when using wire brushes.
DO NOT WORK WITH MATERIALS
WARNING
!
CONTAINING ASBESTOS (ASBESTOS IS
CONSIDERED CARCINOGENIC).
TAKE PROTECTIVE MEASURES WHEN
WARNING
!
DURING WORK DUST CAN DEVELOP
THAT IS HARMFUL TO ONE'S HEALTH, COMBUSTIBLE OR
ExPLOSIVE (SOME DUSTS ARE CONSIDERED CARCINOGENIC);
WEAR A DUST MASK AND WORK WITH DUST/ CHIP
ExTRACTION WHEN CONNECTABLE.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that are
no longer usable must be collected separately and
disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating . . . . . . . . . . . . 7,2 V
Amperage Rating . . . . . . . . . . 1,3 – 1,5 Ah
No Load Speed . . . . . . . . . . . n
Collet Capacity . . . . . . . . . . . 0,8 mm, 1,6 mm, 2,4 mm, 3,2 mm
SPECIFICATIONS CHARGER
Input . . . . . . . . . . . . . . . . . . . . 230 V, 50 – 60 Hz, 26 W
Output . . . . . . . . . . . . . . . . . . 3,6 V - 10,8 V , 1,5 A
ExTENSION CORDS
Use completely unrolled and safe extension cords with a capacity
of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING
ACCESSORIES, CHANGING COLLETS, OR SERVICING THE
TOOL.
5000 – 30000 min
–1
o
IMPORTANT CHARGING NOTES
1. The charger was designed to fast charge the battery only
when the battery temperature is between 32°F (0°C) and
113°F (45°C). If the battery pack is too hot or too cold, the
charger will not fast charge the battery. (This may happen if
the battery pack is hot from heavy use). When the battery
temperature returns to between 32°F (0°C) and 113°F
(45°C), the charger will automatically begin charging.
2. A substantial drop in operating time per charge may mean
that the battery pack is nearing the end of its life and should
be replaced.
3. Remember to unplug charger during storage period.
NOTE: Use of chargers or battery packs not sold by Dremel will
void the warranty.
CHARGING BATTERY PACK (MODEL 808)
Plug charger cord into your standard power outlet.
With no battery pack inserted, the charger's green indicator light
will go ON. This indicates the charger is receiving power and the
charger is ready for operation.
PICTURE 2
A. Tool
B. Battery pack
C. Battery release tabs
To remove the battery pack from the tool press both battery
release tabs and pull the battery from the tool.
When you insert the battery pack into the charger, the charger's
green indicator light will begin to "BLINK". This indicates that the
battery is receiving a fast charge.
PICTURE 3
A. Battery pack
B. Charger
C. Green light
When the indicator light stops "BLINKING" (and becomes a
steady green light) fast charging is complete. The battery pack is
fully charged and can be removed from the charger.
When you begin the charging process of the battery pack, a
steady green light could also mean the battery pack is too hot or
too cold.
Fast charging is only possible when the temperature range of the
battery pack is between 0°C and 45°C.
When needed, the internal fan of the charger will turn on to aid
the charging process and speed.
As soon as the battery pack reaches the correct temperature
range, the battery charger will automatically switch to fast
charging.
The battery pack may be used even though the light may still
be blinking. The light may require more time to stop blinking
depending on temperature.
The purpose of the green light is to indicate that the battery pack
is fast-charging. It does not indicate the exact point of full charge.
The light will stop blinking in less time if the battery pack was not
completely discharged.
21