Milwaukee M18 BLDD2 Notice Originale page 20

TECHNICAL DATA CORDLESS PERCUSSION DRILL/DRIVER
Production code...............................................................................................
Drilling capacity in steel ...................................................................................
Drilling capacity in wood
with fl at bit ....................................................................................................
with auger bit................................................................................................
with hole saw ...............................................................................................
with selfeed bit .............................................................................................
Drilling capacity in brick and tile ......................................................................
Wood screws (without pre-drilling) ..................................................................
No-load speed 1st gear ...................................................................................
No-load speed 2nd gear ..................................................................................
Impact rate 1st gear.........................................................................................
Impact rate 2nd gear .......................................................................................
Torque with battery (5.0 Ah) ............................................................................
Battery voltage.................................................................................................
Drill chuck range ..............................................................................................
Weight according EPTA-Procedure 01/2014 (2.0 Ah) .....................................
Weight according EPTA-Procedure 01/2014 (5.0 Ah) .....................................
Recommended ambient operating temperature ..............................................
Recommended battery types...........................................................................
Recommended charger ...................................................................................
Noise/vibration information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ................................................
Sound power level (Uncertainty K=3dB(A)) .....................................................
Always wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 60745.
Vibration emission value a
h
Percussion drilling into concrete a
Uncertainty K= .............................................................................................
Drilling into metal a ...................................................................................
h,D
Uncertainty K= .............................................................................................
Screwing a ..................................................................................................
h
Uncertainty K= .............................................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent
accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually
doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the hands warm,
organisation of work patterns.
WARNING Read all safety warnings, instructions, illustrations
and specifi cations provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fi re and/or serious
injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Wear ear protectors when impact drilling. Exposure to noise can cause
hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can
cause personal injury.
Hold the power tool by insulated gripping surfaces, when performing
an operation where the cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an electric shock.
Never operate at higher speed than the maximum speed rated of the
drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely
without contacting the workpiece, resulting the personal injury.
Always start drilling at low speed and with the bit tip in contact with
the workpiece. At higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece, resulting the personal injury.
Apply pressure only in direct line with the bit and do not apply
excessive pressure. Bits can bend causing breakage or loss of control,
resulting in personal injury.
SCREWDRIVER SAFETY WARNINGS
Hold the power the tool by insulated gripping surfaces, when
performing an operation where the fastener may contact hidden
wiring. Fasteners contacting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an electric shock.
20 ENGLISH
470 080- M18BLDD2, M18BLPD2.indd 20 470 080- M18BLDD2, M18BLPD2.indd 20
...........................................................
h,ID
M18 BLDD2
............................. 4691 61 01... ..........................4691 72 01...
...000001-999999
...................................13 mm ................................... 13 mm
...................................32 mm ................................... 32 mm
...................................26 mm ................................... 26 mm
...................................89 mm ................................... 89 mm
...................................65 mm ................................... 65 mm
....................................... ......................................... 16 mm
.....................................6 mm ..................................... 6 mm
..............................0-550 min .............................0-550 min
-1
............................0-1800 min ...........................0-1800 min
-1
......................................- min ...........................0-8800 min
-1
......................................- min -1 .........................0-28800 min
...................................82 Nm .................................... 82 Nm
...................................18 V ....................................... 18 V
.............................1,5-13 mm .............................1,5-13 mm
................................1,74 kg ................................... 1,79 kg
................................2,02 kg ................................... 2,07 kg
......................................................... -18...+50 °C
.................................................. M18B...M18HB
........................... M12-18C, M12-18AC, M12-18FC, M1418C6
...................................80 dB (A) ............................... 92 dB (A)
...................................91 dB (A) ............................. 103 dB (A)
....................................... .................................... 11,85 m/s
....................................... ........................................ 1,5 m/s
................................1,86 m/s 2 ................................ 1,86 m/s
..................................1,5 m/s .................................. 1,5 m/s
2
................................2,18 m/s ................................ 2,18 m/s
2
..................................1,5 m/s 2 .................................. 1,5 m/s
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with
the machine. The use of protective clothing is recommended, such as dust
mask, protective gloves, sturdy non-slip footwear, helmet and ear
defenders.
The dust produced when using this tool may be harmful to health. Do not
inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch
the device on again while the insertion tool is stalled, as doing so could
trigger a sudden recoil with a high reactive force. Determine why the
insertion tool stalled and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
Sawdust and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables
and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can
cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
M18 BLPD2
...000001-999999
-1
-1
-1
-1
2
2
2
2
2
2
17.07.2018 11:15:34 17.07.2018 11:15:34