Publicité
Les langues disponibles
Les langues disponibles
Thank you for purchasing this product. Please read user guide for safety
and operations information before using the product. Keep this manual
for future reference. This product can create perfect laser programs and
effects since it has passed a series of strictly tests before delivery. Please
check the attachments listed on the page after opening the carton. In the
event of carton damage or attachment missing in transit, please contact
your dealer or our after sales service department.
CONTENTS OF THE CARTON
1x light effect LAS-500RGB
1x power lead
1x User's manual
Technical specifications
1. Laser diode: DPSS, green 532nm, red650nm, blue450nm
2. Power supply: AC110/220V, 50/60Hz
3. Laser power: B200mW+G60mw +R300mW
4. Motor: 20Kpps
high speed scanners
5. Control mode:sound control/auto/DMX/ILDA
6. Dimensions: 450mm×300mm×120mm
7. Net weight: 7.5KG
8. Gross weight: 8.5 kg
DANGER
LASER RADIATION AVOID EXPOSURE
TO BEAM CLASS 3B LASER PRODUCT
Warning
Do not expose the human eye direct to laser beam.
Do not turn on and off the unit frequently.
Before using this unit make sure the power supply is grounded.
This unit is intended for indoor use only and should be prevented
from water, moisture and shakes. The working temperature of this
unit is 18-30°C, do not use this continuously over 4 hours, otherwise it
shortens the lifetime of the unit.
Use cleaning tissue to remove the dust absorbed on the external
lenses periodically to optimize light output.
Do not remove or break the warranty label, otherwise it void the
warranty.
Always replace with the exact same type fuse, replacement with
anything other than the specified fuse can cause fire or electric shock
and damage your unit, and will void your manufactures warranty.
1
Function setting
Use the dipswitches to assign the unit's function: DMX/slave, sound
active or AUTO mode. For DMX mode, set the DMX address. Each
dipswitch represents a binary value. See the "Function chart".
0=OFF 1=ON X=OFF or ON
DIPSWITCH CHART
#1
#2
#3
#4
#5
#6
#7
0
X
X
X
X
X
X
1
X
X
X
X
X
X
1
1
X
X
X
X
X
X
X
1
X
X
X
X
1
SET DMX ADDRESS FOR DMX
MODE
Sound Active
The change of the laser pattern is controlled by sound. That means the
rhythm of the sound controls the change of the laser pattern. Turn the
sensitivity knob in the clockwise direction to increase the fixture's
sensitivity to sound, turn the knob in the counterclockwise direction to
decrease.
AUTO
Auto cycles the built-in programs without being controlled externally.
DMX Control
The system only accepts the DMX512 signal of international standard to
control the system mode, the laser pattern ON /OFF, the size, the position,
the speed, etc.
Master-Slave Operation
This mode will allow you to link up to 32 units together without controller.
1. Install the units in a suitable position (laying or appending).
2. Choose a unit to function as Master mode, set dipswitch to select
Sound Active or AUTO mode. The others must be set to Slave mode, set
dipswitch to select Slave mode.
Slave units set #3 on
3. Use standard XLR microphone cable chain your units together via the
XLR connector on the rear of the units. For longer cable runs we suggest
a terminator at the last fixture.
4. Turn on the all units' power, the units begin to reset, then the units
begin working. The slave units will react the same as the master unit.
5. The units will react to the low frequencies of music via the internal
microphone. Adjust the audio sensitivity knob on the back of the master
unit to make the unit more or less sensitive in sound active. The panel
has LED indicating for sound active.
2
FUNCTION
#8
#9
#10
X
X
0
SOUND ACTIVE
X
X
0
AUTO -beam
X
X
0
AUTO-animation
X
X
0
Slave for Sound
and Auto
1
DMX
Publicité
