Ventilation System; Servicing And Care; Burner Cleaning; Cleaning The Ash Pan - Bronpi BIO ELSA Instructions D'installation

7.

VENTILATION SYSTEM

The Paula, Brenda and Brenda-E models incorporate a convection turbine as standard, the operation of this turbine is in line with the working
power of the model, so that with the stove switched on, the turbine will always remain in operation. The model Elsa has the possibility to active
or deactivate the convection turbine of the stove. By using the remote control, you can activate the operation of the turbine. In this way, the
stove will heat the air through the own radiation of the stove and the forced convection of the turbine.
In case you choose to deactivate the operation of the turbine, the heating of the air will be generated by the radiation of the stove and, in this
case, by natural convection.
In order to active or deactive the operation of the turbine, check section 10.4.3.1 of this manual "power".
8.

SERVICING AND CARE

The maintenance operations guarantee a proper working of the product over its lifetime. Not making these maintenance operations will affect
the security of the product.
8.1

BURNER CLEANING

On the other hand, in the models Brenda, Brenda-E and Elsa, the burner
cleaning must be made daily (see drawing D18).
• Remove the burner from its place and clean the holes.
• Use a vacuum to get rid of the ashes in the burner. You can buy a
Bronpi vacuum-cleaner in the same Bronpi distributor where you bought
your stove.
D19
8.2

CLEANING THE ASH PAN

The ash pan should be emptied when necessary. The stove
should not be operated without having the ash pan inside
(see drawing D20).
8.3 SEALS OF THE COMBUSTION CHAMBER AND
GLASS FIBRE
The seals of the doors guarantee stove hermetic nature and,
thus, a proper performance (see drawing D21).
It is necessary to check them regularly; if they are worn-out
D21
8.5

CLEANING THE GLASS

IMPORTANT:Clean the glass only when it is cold in order to avoid possible explosion. You can use specific products. You
can find Bronpi vitro ceramic-cleaning product at the same Bronpi distributor where you bought your stove (see drawing
D22).
BREAKAGE OF GLASSES. The glasses, as they are vitro ceramic, resist until 750ºC and they are not subject to thermal
shocks. The breakage can only be caused by mechanical shocks (crashes or violent closing of the door, etc). Therefore, its
replacement is not included in the warranty.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
or damaged they should be replaced immediately. You can find ceramic cord and self-adhesive fibre at the
same Bronpi distributor where you bought your stove.
These operations should be done exclusively by an authorised technician.
An authorised technician must do the maintenance at least once a year.
8.4

CLEANING THE CHIMNEY

When the pellet is burnt slowly, it produces tar deposits and other organic vapours that combined with the
humidity to create soot (creosote). An excessive accumulation of soot may cause problems in the smoke outlet
and the flue may catch fire if not maintained.
The cleaning of the stove chimney should only be made when the equipment is cold. A chimney sweep should
perform this task and, at the same time, examine the smoke duct (it is recommended to write down the dates
of every cleaning and keep a register of them).
In the Paula model, the burner is cleaned periodically and
automatically (cleaning system registered by Bronpi Calefacción),
but at least every 10 days, it is advisable to do a manual cleaning
of the burner, for this (see drawing D19):
• Vacuum the ash deposited in the burner. You can purchase
a Bronpi vacuum cleaner in the same Bronpi dealer where you
bought your stove.
• Check and if necessary clean the holes in the base of the
burner so that they are not blocked. This would make difficult a
good combustion.
36
D20
ELSA, PAULA, BRENDA AND BRENDA-E
D18
D22