Service And Maintenance - Festool OF 1400 EQ Notice D'utilisation D'origine

English
An extractor hose with a diameter of
27 mm or 36 mm should be connected at
the extractor connector [5-3].
8.3 Routing with the FS guide system
The guide system (available as an accessory)
makes it easier to route straight grooves.
► Secure the guide rail adapter [6-1] to the
router table using the guide rods [6-8] of
the parallel side fence.
► Secure the guide rail [6-3] to the workpiece
using fastening clamps [6-4].
Ensure that there is a safety distance X of
(see figure [6]) 5 mm between the front
edge of the guide rail and the cutter, or the
groove.
► Place the guide rail adapter on the guide
rail, as shown in figure [6]. To ensure that
the router stop can be guided without play,
use a screwdriver through the top open­
ings [6-2] on the side to adjust the two
guidance jaws.
► Tighten the height-adjustable support [6-6]
on the threaded hole of the router table so
that the underside of the router table is par­
allel to the workpiece surface.
When working with marking-up lines, the
marks on the platen [6-5] and the scale on the
support [6-6] show the centre axis of the cutter.
Fine adjuster
The fine adjuster (available as an accesso­
ry, [7-5]) can be used to precisely adjust dis­
tance X.
► Install the fine adjuster [7-5] on the guide
rods between the power tool and the guide
rail adapter [7-4].
► Insert the adjusting wheel [7-2] into the
guide rail adapter, as shown in the fig­
ure [7].
► Screw the adjusting wheel [7-2] into the
nuts of the fine adjuster.
To adjust distance X:
► Open the rotary knob [7-1] for the guide rail
adapter and close the rotary knob [7-3] for
the fine adjuster.
► Adjust to required distance X by turning the
adjusting wheel [7-2].
► Close the rotary knob [7-1] for the guide
rail adapter.
8.4 Copy cutting
A copying ring or the copying device is used to
exactly reproduce existing workpieces (acces­
sories).
20
Copying ring
When choosing the size of the copying ring, en­
sure that the cutter being used fits through its
opening.
Excess Y (figure [9]) of the workpiece to the
template is calculated as follows:
Y = (copying ring diameter - cutter diameter)/2
► Attach the copying ring [8-1] to the router
table: Insert the two tenons [8-2] into the
recesses [8-3].
► To remove the copying ring: Press the two
buttons [1-16] inwards at the same time.
Copying device
The copying device requires the angle arm WA-
OF [10-2] and the copier scanning set KT-OF,
consisting of a roller support [10-6] and three
copying rollers [10-7].
► Use the rotary knob [10-3] to tighten the
angle arm to the required height on the
threaded hole [10-1].
► Fit a copying roller to the roller support and
use the rotary knob [10-5] to tighten it on
the angle arm. Make sure that the copying
roller and the router have the same diame­
ter.
► The distance between the feeler roller and
the cutter axis can be adjusted by turning
the adjusting wheel [10-4].
9

Service and maintenance

WARNING
Risk of injury, electric shock
► Always pull the mains plug from the socket
before performing any servicing and main­
tenance work.
► All maintenance and repair work which re­
quires the housing to be opened should al­
ways be carried out by an authorised serv­
ice workshop.
Customer service and repairs must
only be carried out by the manufac­
turer or service workshops. Find the
nearest address at:
www.festool.co.uk/service
Always use original Festool spare
EKAT
4
parts. Order no. at:
www.festool.co.uk/service
5
3
2
1
The tool is equipped with special self-discon­
necting carbon brushes. If they wear out, the