Copy Cutting; Edge Band Trimming; Service And Maintenance - Festool OF 1010 REBQ Notice D'utilisation

English
that the underside of the router table is par­
allel to the workpiece surface.
When working with marking-up lines, the
marks on the platen [7-1] and the scale on the
support [7-2] show the centre axis of the cutter.
For a more precise setting, a fine adjust­
ment is available as an accessory for the
guide system.
8.4 Routing with the beam compasses
With the SZ-OF 1000 beam compasses (acces­
sory) you can make circular cuts or segments
of circles with diameters from 153 to 760 mm.
► The beam compasses are pushed into the
front groove of the platen until the desired
radius is set.
► Lock the beam compasses with the rotating
knob [1-4].
To prevent the tip of the compasses
from making a hole in the workpiece,
fix a thin board at the centre point by
means of double-sided adhesive tape.
8.5

Copy cutting

A copying ring or the copying device is used to
exactly reproduce existing workpieces (acces­
sories).
Copying ring
When choosing the size of the copying
ring [5-1], ensure that the cutter [5-2] being
used fits through its opening.
► Secure the copying ring to the router table
from below in place of the covering
ring [4-1].
Excess Y (figure [5]) of the workpiece to the
template is calculated as follows:
Y = (copying ring diameter - cutter diameter)/2
The copying ring can be exactly centred with the
ZD-OF centring mandrel (accessory).
Copying device
The copying device requires the angle arm WA-
OF [8-2] and the copier scanning set KT-OF,
consisting of a roller support [8-6] and three
copying rollers [8-7].
► Use the rotary knob [8-1] to tighten the an­
gle arm to the required height on the threa­
ded hole [8-3].
► Fit a copying roller to the roller support and
use the rotary knob [8-5] to tighten it on the
angle arm. Make sure that the copying roll­
er and the router have the same diameter.
20
► The distance between the feeler roller and
the cutter axis can be adjusted by turning
the adjusting wheel [8-4].
8.6

Edge band trimming

Protruding edge bands can be flush trimmed
with the angle arm WA-OF [9-2] in connection
with the guide plate UP-OF [9-5] (accessory).
► Screw the angle arm into the platen's
threaded bore [9-1] with the rotating
knob [9-3].
► Bolt the guide plate to the angle arm with
the rotating knob [9-4].
► Adjust the milling depth so that this is equal
to the thickness of the edge band + 2 mm.
Move the guide plate [10-1] as close as
►
possible to the cutter by loosening the ro­
tating knob [10-3].
► Adjust the depth of the guide plate with the
adjusting wheel [10-2] so that during trim­
ming a few decimillimetres of the edge
band are left protruding which can then be
sanded down by hand.
9

Service and maintenance

WARNING
Risk of injury, electric shock
► Always pull the mains plug from the socket
before performing any servicing and main­
tenance work.
► All maintenance and repair work which re­
quires the housing to be opened should al­
ways be carried out by an authorised serv­
ice workshop.
Customer service and repairs must
only be carried out by the manufac­
turer or service workshops. Find the
nearest address at:
www.festool.co.uk/service
Always use original Festool spare
EKAT
4
parts. Order no. at:
www.festool.co.uk/service
5
3
2
1
The tool is equipped with special self-discon­
necting carbon brushes. If they wear out, the
power supply is disconnected automatically and
the tool stops.
Observe the following instructions:
► Damaged safety devices and components
must be repaired or replaced in a recog­
nised specialist workshop, unless otherwise
indicated in the operating instructions.