Unpacking; Attachment / Before Starting The Equipment - Scheppach HS410 Traduction Des Instructions D'origine

sound power level L 115 dB(A) (EN ISO 3744)
WA
sound pressure level L 101 dB(A) (EN ISO 11201)
pA
uncertainly K 4 dB(A)
pA

8. Unpacking

Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage.
In case of complaints the dealer must be informed
immediately. Subsequent complaints will not be ac-
cepted.
If possible, store the packaging until the warranty pe-
riod has expired.
Read the operating manual to make yourself familiar
with the device prior to using it.
Only use original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer.
Specify our part numbers as well as the type and year
of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
9. Attachment / Before starting the
equipment
m IMPORTANT!
You must fully assemble the appliance before using it
for the first time!
Assembly
Swivel frame (9) (fig. 4 - 8)
Position the (right) guard (18) at the outer side of the
fastening and the saw blade guard 1 (20) at the inner
side of the fastening. Fasten the two steel panel parts
with three flat, rounds screws and nuts (A1). Fasten
the guard (18) to the swivel frame with the hex screws
and nuts (A2). (Fig. 4 - 5)
Repeat this process to fit the (left) guard (19) and saw
blade guard 2 (21). (Fig. 6 - 7)
Position the handle (10) on the left side of the swiv-
el frame and secure this firmly with the cylindrical
screws and nuts (B1). (Fig. 8)
Return spring (11) & locking lever (11a) (fig. 9)
Position the return spring (11) on the inner side and
the locking lever (11a) on the outer side of the swivel
frame and fasten these with the hex screw and nut
(D). Do not tighten the screw too tightly to ensure
that the locking lever (11a) can still be easily moved.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Combination switch/plug (3) (fig. 10)
Fasten the combination switch/plug on the rear of
the main frame (5) with the Phillips head screws and
nuts (C).
Cross member (6) (fig. 11)
Open the main frame (5) out and attach the cross
member. One end of the cross member is fitted to the
inner side of the main frame (motor side). Fasten the
cross member loosely initially using the hex screw
and the nut (E1).
Now place the swivel frame on the "swivel side" of the
main frame. The other end of the cross member can
now be attached to the outer side of the main frame.
Screw the cross member and the swivel frame firmly
onto the main frame (5) with the hex screws (E2).
Then tighten screw (E1) firmly too.
Saw blade guard & saw blade (fig. 12 - 15)
Position the saw blade guard (2) as shown in Figure
12. Fasten this in place with the three fillister head
screws and nuts (F1) at the top part of the saw blade
guard. Fasten the bottom part of the saw blade guard
with the fillister head screw and nut (F2).
Now fit the flange (24) to the motor shaft (4).
Position the saw blade (23) on the flange (24) and in
doing so ensure that the teeth of the saw blade are
pointing in the correct direction. Then fit the flange
(22) and fasten the complete assembly with the hex
nut (G).
Tighten the hex nut (G) with the installation tool (25)
provided as shown in fig. 14.
Fit the saw blade guard (14) and fasten this with the
Phillips head screws (H).
Setting up the swivel frame (9) (fig. 16 - 18)
First remove the spring split pin (16a) and the washer
and keep these in your hand temporarily. Now open
out the swivel frame (9) and ensure that the return
spring does not fly off. Feed the rod of the return
spring through the hole provided for it. Finally, fasten
the return spring using the spring split pin removed
previously.
Now fasten the chain (12) with the hex screw (I1)
(fig. 16).
Fasten the guide (17a) onto the threaded rod provid-
ed for it with the self-locking nut (I2).
Finally, fit the guard (17) and fasten this in place with
the two Phillips head screws (J).
Guard (7) (fig. 19)
Fit the guard as shown in Figure 19. Feed the collar
bushings into the three holes on the bracket for the
guard. Then fasten the guard in place with the three
screws (K).
GB | 25