Publicité
Les langues disponibles
Les langues disponibles
PROGRAMMING THE SENSOR
SENSOR
PROGRAMMING
BUTTON
NOTE: These steps are only required if using the computer with a 2nd bike and only need
to be done once. Complete these steps after the computer is programed and the sensor
is installed.
1. Install the computer on bike 2.
2. Press the blue SeNSOR PROGRAMMING buTTON on the back of the SeNSOR INDICATOR
LeD flashes. Release the button.
3. Lift the front wheel off the ground and spin it. The bike 1 icon " " will switch to the bike
2 icon " " and begin recording information for bike 2.
4. Verify final set up for bike 2 " by pressing the blue SeNSOR PROGRAMMING buTTON.
The LeD will flash twice for bike 2.
5. To verify final set up for bike 1, reinstall the computer on bike 1. Lift and spin the
front wheel to start the computer. Stop the wheel then press the blue SeNSOR
PROGRAMMING buTTON The SeNSOR INDICATOR LeD will flash 1 time to verify proper
function with bike 1.
SETTING CALORIES BURNED (KCAL)
This computer can estimate calories burned while riding. The estimate is based on weight,
gender, time ridden and average speed. IMPORTANT: The estimate is truly an estimate.
Actual calories burned will vary depending on many variables the computer does not
calculate such as heart rate.
1. Press FUNCTION until the "KCAL" displays.
2 Press and hold SET for >3 seconds to begin programming.
3. Press SET to select gender "MALE" or "FEMALE".
4. Press FUNCTION to store gender.
5. Press SET to change weight unit "kg" or "Lb".
6. Press FUNCTION to begin entering your weight in unit selected.
7. Press or hold Set to change the weight. Range: 0 ~ 150 kg, 0-330 Lb.
8. Press and hold the Function for 3 seconds to exit programming.
RESETTING THE ODOMETER (ODO)
If the battery is replaced, it is possible to update the odometer to the mileage on your bike
after replacing the battery.
1. Press FUNCTION until the "ODO" displays.
2. Press and hold SET for >3 seconds to begin programming.
3. Press FUNCTION until "00000" (five zeros) and "ODO" appears on the screen
4. Press SET to change the appropriate numbers. Press FUNCTION to change cursor
position.
5. Repeat step 4 until the odometer is set.
6. Press and hold FUNCTION for 3 seconds to exit programming.
SETTING THE TEMPERATURE
1. Press FUNCTION until "ODO" displays.
2. Press and hold SET for >3 seconds to begin programming.
SENSOR
INDICATOR LED
3. Press FUNCTION repeatedly until "TEMP" displays.
4. Press and hold FUNCTION for 3 seconds to exit programming.
BATTERY REPLACEMENT
Remove the computer from the handlebar mount. use a coin to unscrew the battery door.
Turn counter-clockwise. Remove the old battery. Place a new battery (CR2032) into the
computer with the positive "+" marking of the battery facing up. Replace the battery door.
Follow these steps for replacing the sensor battery (CR2032).
IQ300 Specifications
Operating Temperature
Storage Temperature
battery
Weight
Timer Range: 0~29 (hour): 59 (minute): 59 (second)
Current Speed Range: 0 ~ 99.9 kM/ 0~62 Mile
Average Speed Range: 0 ~ 99.9 kM/ 0~62 Mile
MAX Speed Range: 0 ~ 99.9 kM/ 0 ~ 62 Mile
(Trip) Distance Range: 0 ~ 999.99 kM/ 0~600 Mile
Odometer Range: 0 ~ 99999 kM/ 0 ~ 62000 Mile
TROUBLESHOOTING
CONDITION
Wheel moving but current speed does not
appear
"eRR01" appears on display
"eRR" appears on display
Display is blank, very light or black
Display changes slowly
NOTE: Touch feature is activated by finger pressure. If gloves are to thick, such
as winter gloves, the FuNCTION button may not be activated and require more
pressure.
NOTE: The computer uses a pencil tip sized free-floating sensor for auto on/off
features. If you hear a rattling noise during excessive vibration, it is normal and
the function will not be effected.
CANNONDALE CONTACT INFORMATION
2012 IQ300 Computer
Setup and Owners Manual - 11/11
Press SET to change Fahrenheit (F) or Celsius (C)
CANNONDALE USA
Cycling Sports Group, Inc.
172 Friendship Road,
bedford, Pennsylvania, 15522 , uSA
(Voice): 1-800-bIke-uSA
(Fax): 814-623-6173
custserv@cyclingsportsgroup.com
CANNONDALE AUSTRALIA
Cycling Sports Group Australia Pty Limited
unit 8, 31-41 bridge Road
Stanmore, NSW 2048, Australia
(Voice): 61-2-85954444
(Fax): 61-2-85954499
cannondale@cyclingsportsgroup.com.au
CANNONDALE UK
Cycling Sports Group
Vantage Way, The Fulcrum,
Poole, Dorset, bH12 4Nu
(Voice): +44 (0)1202 732288
(Fax): +44 (0)1202 723366
sales@cyclingsportsgroup.co.uk
0° C ~ 40° C, ( 32° F ~ 104°F)
-10° C ~ 50° C, ( 14° F ~ 122°F)
3 volt lithium, CR2032 cell
30.6 grams
ACTION
Check/adjust sensor and magnet gap.
battery is low –> replace
battery low –> replace
Interference from another electronic
device-> turn off or move electronic
device
battery low –> replace.
Computer too hot –> move to cool area.
Computer too cold –> move to warm
area
CANNONDALE EUROPE
Cycling Sports Group europe, b.V.
mail: Postbus 5100
visits: Hanzepoort 27
7570 GC, Oldenzaal, Netherlands
(Voice): + 41 61.4879380
(Fax): 31-5415-14240
servicedeskeurope@cyclingsportsgroup.com
CANNONDALE JAPAN
Namba Sumiso building 9F,
4-19, Minami Horie 1-chome,
Nishi-ku, Osaka 550-0015, Japan
(Voice): 06-6110-9390
(Fax): 06-6110-9361
cjcustserv@cannondale.com
Publicité
