Cannondale IQ300 Manuel D'installation Et D'utilisation page 2

Main DiSpLay anD FuncTionS
touch
TEMPERATURE
CURRENT SPEED
MOTION SIGNAL
SPEED SCALE
SLEEP MODE
FUNCTIONS DISPLAY
BIKE "I or BIKE "II"
SUB-DISPLAY
FUNCTION Button
To begin using the computer, simply press the FUNCTION button. Following installation,
the computer is activated automatically by a rotating wheel.
There are 2 power saving modes - 50% savings if no movement after 5 minutes, 100%
power savings after 30 minutes.
Press the SET button to exit the power saving modes prior to using the computer.
Press the FUNCTION button, to switch the computer through the following functions:
"CLK" – Clock feature, in 12/24 hr format
"TM" – Time ridden for 1 ride
"AVS" – Average speed for 1 ride
"MXS" – Maximum speed for 1 ride
"DST" - Distance ridden for 1 ride
"ODO" – Total miles ridden for all rides
"KCAL" – Calories burned (estimate) for 1 ride
"DAILY" -- DIstance ridden in the past 24 hours
"ODO 1" -- Total miles for all rides, bike 1 " "
"ODO 2" -- Total miles for all rides, bike 2 " "
To turn on the backlight, press and release the SET button. The backlight will stay
on for three (3) seconds.
"TM, AVS, MXS, DST, and kCAL " are recorded automatically as soon as the wheel moves.
Recording stops if the wheel stops. To clear this information, press and hold the SET
button in the "TM" mode.
GENERAL NOTES FOR PROGRAMMING ALL FUNCTIONS:
Press and hold SET for 3 seconds to begin programming a function.
•
Press the SET to change the value of a selected field. Press/hold SeT to change
•
value rapidly.
• Press the FUNCTION button to move the cursor to the next field.
Press and hold the FUNCTION button for 3 seconds to exit programming.
•
SETTING THE CLOCK (CLK)
1. Press FUNCTION until the "CLK" function shows.
2. Press and hold SET for >3 seconds to begin programming.
3. Press SET to change to "12H" or "24H" hour mode.
4. Press the FUNCTION to move the cursor to the hour field
5. Press SET hour.
6. Repeat steps 4 and 5 to set Minutes and Seconds.
7. Press and hold the FUNCTION button for 3 seconds to exit programming.
**This button also,
activates the display
backlighting.
MODE
SETTING THE WHEEL SIZE
NOTE: This computer can record information for 2 bikes with different wheel sizes. This
allows you to use 1 computer for 2 bikes. Shortly after the wheel rotates, the computer
automatically knows which bike is being used then provides accurate information for
SET Button
speed and mileage. A mounting kit for a 2nd bike is sold separately. The following steps
(back of unit)
only need to be done once.
To start programming:
1. Press FUNCTION until "ODO" displays.
2. Press and hold SET for >3 seconds to begin programming.
3. Press SET to change to "kM/H" or "M/H"
To program the computer for bike #1:
4. Determine your Tire Size then find the corresponding L (mm) in the chart below.
5. Press SET to select bike 1 " "
6. Press FUNCTION to move the cursor to the first field.
7. Press SET to change the 1st digit of 4 numbers for the L (mm).
Repeat steps 6 and 7 until the proper L (mm) is entered.
If you will use this computer for 2 bikes, continue to step 8.
If you will use it for only 1 bike, continue to step 10.
To program the computer for bike #2:
8. Determine your Tire Size then find the corresponding L (mm) in the chart below.
9. Press FUNCTION to select bike 2 " "
Repeat steps 6 and 7 until the proper L (mm) is entered.
10. Press and hold FUNCTION for 3 seconds to exit programming.
14 X 1.50
14 x 1.75
16 X 1.50
16 X 1.75
18 X 1.50
18 X 1.75
20 X 1.75
20 X 1-3/8
22 X 1-3/8
22 X 1-1/2
24 X 3/4 Tubular
24 x 1-1/8
24 X 1-1/4
2012 IQ300 Computer
Setup and Owners Manual - 11/11
Tire Size
L (mm)
24 X 1.75
24 X 2.00
24 X 2.125
26 X 7/8
26 X 1(59)
26 X 1(65)
26 X 1.25
Tire Size L (mm) 26 X 1-1/8
1020 26 X 1-3/8
1055 26 X 1-1/2
1185 26 X 1.40
1195 26 X 1.50
1340 26 X 1.75
1350 26 X 1.95
1515 26 X 2.00
1615 26 X 2.10
1770 26 X 2.125
1785 26 X 2.35
24 X 1 1753 26 X 3.00
1785 27 X 1
1795 27 X 1-1/8
1905 27 X 1-1/4
L (mm) Tire Size L (mm)
1890 27 X 1-3/8 2169
1925 650 X 20C 1938
1965 650 X 23C 1944
1920 650 X 35A 2090
1913 650 X 38A 2125
1952 650 X 38b 2105
1953 700 X 18C 2070
1970 700 X 19C 2080
2068 700 X 20C 2086
2100 700 X 23C 2096
2005 700 X 25C 2105
2010 700 X 28C 2136
2023 700 X 30C 2146
2050 700 X 32C 2155
2055 700C Tubular 2130
2068 700 X 35C 2168
2070 700 X 38C 2180
2083 700 X 40C 2200
2170 29 X 2.1 2288
2145 29 X 2.3 2326
2155
2161