Technical Data; Safety Instructions - Cooper Crouse-Hinds 16A Mode D'emploi

2

Safety instructions

The maintenance sockets are not
suitable for Zone 0 hazardous
areas.
The requirements of the EN 61241-0 and -1
regarding excessive dust deposits and
temperature to be considered from the
user.
Attention:
The maintenance sockets shall be
secured on the hinged cover (bayonet
ring) against unauthorized use by means
of a padlock (shakle Ø = 5mm).
Operation of the maintenance sockets is
only permitted if a hot work permit has
being issued.
Before switching on, ensure that there is
not exist explosive gas atmosphere.
The temperature class and explosion group
marked on the apparatus shall be
observed.
The electrical connection of the device may
only be carried out by skilled staff.
To ensure adherence to the temperature
class stated on the type label of the
apparatus, the permissible ambient
temperature, the rated terminal cross
section and the self heating of the
apparatus that is mainly due to the power
dissipation shall be taken into account (test
criterion for the self heating is an overload
of 10%).
For replacement and repair only genuine
CCH / CEAG spare parts shall be used.
Repairs that affect the explosion
protection, may only be carried out by
CCH / CEAG or a qualified electrician in
compliance with the respective national
regulations.
Prior to taking the plugs and sockets into
operation, they will have to be checked in
accordance with the instruction as per
section 6.
The interlocking switch of the socket is
mechanically secured and cannot be
connected without plug.
Observe the national safety rules and
regulations for prevention of accidents as
well as the safety instructions included in
these operating instructions and set in
italics the same as this text!
6 6 6 6 6 Cooper Crouse-Hinds GmbH
Maintenance sockets, 16A, 32A, 63A, 125A
1

Technical data

Marking acc. to 94/9/EC:
EC-type examination certificate:
Rated voltage:
Perm. ambient temperature:
other temperatures possible for special versions.
Perm. storage temperature in original packing:
Protection category acc. to EN/IEC 60529
with closed and secured hinged cover, as well
as correctly inserted combinations:
Insulation class acc. to EN/IEC 61140:
Cable entry (standard version):
Test torques:
Cap nut of the entry
for min. cable Ø in Nm
for max. cable Ø in Nm
Auxiliary contact, rated voltage:
Auxiliary contact, rated current:
1.1 Maintenance socket GHG 511, 16A, locked
Rated current:
Back-up fuse:
without thermal protection
with thermal protection
Switching capacity AC 3:
Cable entry (standard version):
Supply terminal:
Test torques:
Cover screws
Terminals
Weight (standard version):
1.2 Maintenance socket GHG 512, 32A, locked
Rated current:
Back-up fuse:
without thermal protection
with thermal protection
Switching capacity AC 3:
Cable entry (standard version):
Supply terminal:
Test torques:
Cover screws
Terminals
Weight (standard version):
1.3 Maintenance socket GHG 514, 63A, locked
Rated current:
Back-up fuse:
without thermal protection
with thermal protection
Switching capacity AC 3:
Cable entry (standard version):
Supply terminal:
Test torques:
Cover screws
Terminals
Weight (standard version):
Auxiliary contact, rated voltage:
Auxiliary contact, rated current:
Auxiliary contact, switching capacity:
II 2 G Ex de II C T6 / T5
II 2 D Ex tD A21 IP 66 T80°C/T95°C
PTB 00 ATEX 1032 X
up to 415 V, 50/60 Hz
-20° C to +40° C (standard version)
-40° C to +80° C
IP 66 (standard version)
I - is complied with by the devices
1xM25 (Ø 8-17mm) +1xblanking plug M25
M20 M25
3.50 5.00
2.50 3.50
250 V
250 VAC 1 / 5 A
max. 16 A
max. 16 A
max. 35 A gL
2-pole+PE
250V/16A
2xM25 1 x Ø 8-17mm +1 x screwed blanking plug
Cross section
2 x 1.5 - 4 mm²
2.5 Nm
2.5 Nm
2-pole+PE
ca. 1.10 kg
max. 32A
max. 32A
max. 50A gL
415V/32A
2xM40 1 x Ø 17-28mm +1 x screwed blanking plug
Cross section
2 x 4.0 - 10 mm²
2.5 Nm
3.5 Nm
2-pole+PE
ca. 2.20 kg
max. 63A
max. 63A
max. 80A gL
415V/63A
2xM50 1 x Ø 26-34mm +1 x screwed blanking plug
Cross section
2 x 4 - 25 mm² *
* (with cable lugs 1 x 35 mm²)
2.5 Nm
3.0 Nm
3-pole+PE
ca. 8.10 kg
415V AC
20A
AC 15 400V / 4A
M32 M40 M50 M63
8.00 11.00 16.00 22.00
5.00 5.00 5.00 5.00
250 VDC 1 / 0.25 A
3-pole+PE 4-pole+PE
400V/16A 400V/16A
Stripped wire length
10 mm
3-pole+PE 4-pole+PE
ca. 1.50 kg ca. 1.55 kg
Stripped wire length
12 mm
3-pole+PE 4-pole+PE
ca. 2.25 kg ca. 2.30 kg
Stripped wire length
19 mm
4-pole+PE
8.15 kg
DC 13 24V / 1A