Candy PG2D750/1 SX Notice D'emploi page 23

To prevent any potential damage to the hob please carry out the installation following
this sequence:
GB IE
1/2 GAS
CONICAL
A) As illustrated, as- 2) Tighten the joints
semble parts in se- with the Spanners,
quence: remembering to twist
A) fixed pipe the pipes into position.
B) washer
C) Elbow fitting with
tapered thred
connection
For some models a conic link is furnished to outfit for the installation in the countries whe-
re this type of link is obligatory; in the following figures it is pointed out how to recognize
the different types of links. In every case the cylindrical part of the link has to be connec-
ted to the hob.
Fig. 5
ADAPTING THE HOB TO DIFFERENT TYPES OF GAS
To adapt the Hob for use with different types of gas, carry out the following instructions:
— remove the grids and burners
— insert on hexagonal spanner (7 mm) into the burner support (Fig. 6)
— unscrew the injector and replace it with one suitable for the gas to be used (see
Table of gas consumption)
GB IE
3) Attach fitting C to
mains gas supply us-
ing rigid copper pipe
or flexible steel pipe.
CYLINDRICAL
CONICAL
INJECTOR
Fig. 6
43
Table of gas consumption
G20 G30 GZ 350 G20 20mbar G30 28-30mbar
G25 G31 G31 37mbar GZ350 13mbar
Working ø gas jet ø gas jet
ø gas jet Qn Qmin
burner 1/100 mm 1/100 mm
1/100 mm
kW W
little 76 50 104 1 230
large 101 66 132 1,75 360
medium 118 80 160 2,5 530
maxi 144 94 190 3,5 700
double ring 141 96 191 3,5 1750
REGULATING THE MINIMUM FLAME
After lighting the burners, turn the control knob to the minimum setting and then remo-
ve the knob (this can easily be removed by apply a gentle pressure).
Using a small «Terminal» type screwdriver the regulating screw can be adjusted as in
Fig. 7. Turning the screw clockwise reduces the gas flow, whilst turning it anticlockwise
increases the flow – Use this adjustment to obtain a flame of approximately 3 to 4 mm
in length and then replace the control knob.
When the gas supply available is LPG (Bottle gas)- the screw to set the idle flame must
be turned (clockwise) to the end stop.
Screws regulating
(for differend models)
Fig.7
When you have carried out the new gas regulation, replace the old gas rating pla-
te on your appliance with one (supplied with hob) suitable for the type of gas for
which it has been regulated.
USE OF HOB
USER INSTRUCTIONS
This appliance must only be used for the purpose for which it is intended, domestic
cooking, and any other use will be considered improper and could therefore be danger-
ous. The Manufacturer will not be responsible for any damage or loss resulting from
improper use.
1 W 0,860 Kcal/h
G20 25mbar
G30 36mbar
l/h l/h g/h g/h Qn Qmin l/h g/h Qn
G20 GZ350 G30 G31 kW W G20 G30 kW
95 132 73 71 1,2 260 114 87 0,9
167 232 127 125 2 410 190 145 1,6
238 331 182 179 2,8 620 267 204 2,25
333 463 254 250 4 830 381 291 3,2
333 463 254 250 4 1900
381 291 3,2
44
G25 25mbar
G31 30mbar
Qmin l/h g/h
W G25 G31
230 100 64
360 177 114
530 255 161
700 354 229
1750 354 229
IE GB