Time; Changing The Basic Settings - Blaupunkt 5BD350 Série Notice D'utilisation

Tap the sensor.
0
4.
The time at which the dish will be ready and the
symbol appear in the display panel.
Set a later end time using
5.
Tap the ºC sensor.
6.
Using or , set the required temperature or grill setting.
@ A
The set temperature and the
display panel; the oven is in standby. As soon as the oven is
switched on, the set temperature and the
displayed. The symbol goes out.
y
The cooking time has finished
A beep will sound. The oven will stop heating. The display
panel will show : . Press the
‹‹ ‹‹
a new cooking time with the
sensor and turn the function control knob to zero. The oven is
switched off.

Changing the basic settings

This oven has different basic settings. The settings can be
adapted to the user's own needs.
Basic setting
Duration of signal after the cooking time or the time set on the
™‚
timer has elapsed
Time indicator
™ƒ
Time until a setting is applied
™„
The shelf support rails have been refitted.
™†
Select default settings for all values.
™‡
* Default setting
The oven must be switched off.
Press the sensor for approximately 4 seconds.
0
1.
The display panel will show the current basic setting for the
duration of the signal, e.g.,
Change the basic setting using the
2.
y End
or .
@ A
symbol are displayed in the
y
symbol are
x
sensor twice. You can set
0
or sensors, or press the
@ A
™‚ Option ƒ .
or sensors.
@ A
Changing the end time
Press the sensor
the or sensors. The altered time is shown after a few
@ A
seconds. Do not change the end time if the cooking time has
already started to count down. The final result may not be the
same.
Cancelling the end time
Press the sensor three times and reset the end time to the
0
current time with the
Viewing the time settings
If several time functions are programmed, the corresponding
symbols light up on the display panel.
To view the timer
the time , press the
0
symbol lights up. The corresponding value will be shown for a
few seconds on the display panel.

Time

Once the oven has been connected or after a power cut, the
and : symbols light up on the display panel.Set the clock
‹ ‹‹
to the right time.
Press the sensor.
0
1.
The time is displayed
Set the time with the
2.
Confirm the time with the
3.
The programmed time is displayed after a few seconds.
Changing the time
No other time function must be programmed, the oven must be
switched off.
Press the sensor twice.
0
1.
The display panel displays
Set the time with the
2.
Confirm the time with the
3.
The programmed time is displayed after a few seconds.
0
Hiding the time
The time can be hidden. See the Modifying basic settings
chapter.
Option 0 Option 1
- approx. 10 sec approx. 2 min* approx. 5 min
no yes*
- approx. 2 sec
no yes
no* yes
Confirm with the sensor
3.
The display panel shows the following basic setting. The
sensor allows you to run through all the settings and the
A sensors allow you to modify them.
Finally, press the
4.
All basic settings have been applied.
The basic settings can be changed again at any time.
three times. Change the end time using
0
sensor. The oven switches on.
A
, the cooking time , the end time
V x
sensor repeatedly until the required
0
‚ƒ : ‹‹ .
or sensors.
@ A
sensor.
0
.
0
@ or A sensors.
0 sensor.
Option 2
-
approx. 4 sec* approx. 10 sec
-
-
.
0
sensor for approximately 4 seconds.
0
or
y
0
Option 3
-
-
-
0
or
@
35