Fitting the handle (Fig. 4)
Use a screwdriver to fi t the handle (1).
5.2 Fitting the fi lters
Caution!
Never use the wet and dry vacuum cleaner wit-
hout a fi lter.
Always ensure that the fi lters are securely seated.
Fitting the foam fi lter (Fig. 7)
For wet vacuuming, slip the supplied foam fi lter
(16) over the fi lter basket (Fig. 2/4). The pleated
fi lter (15) already fi tted upon delivery is not suita-
ble for wet vacuuming.
Fitting the pleated fi lter (Fig. 8)
For dry-vacuuming, slip the pleated fi lter (Fig. 15)
over the fi lter basket (Fig. 2/4). The pleated fi lter
(15) is suitable for dry-vacuuming only.
Fitting the dirt bag
(not supplied)
For vacuuming fi ne, dry dirt it is recommended
that you also fi t the dirt bag. This will ensure that
the pleated fi lter (15) does not clog up so quickly
and help maintain the vacuuming power. It also
makes it easier to dispose of the dust. Slip the
dirt bag over the vacuuming hole. The dirt bag is
suitable for dry-vacuuming only.
5.3 Fitting the suction hose (Fig. 9-12)
Connect the suction hose (11) to the correspon-
ding connector on the wet and dry vacuum clea-
ner, depending on the application required.
Vacuuming
Connect the suction hose (11) to the suction hose
connector (9).
Blowing
Connect the suction hose (11) to the blow con-
nector (10).
To extend the suction hose (11) you can attach
one or more of the elements which make up the
3-part suction tube (12) to the suction hose (11).
5.4 Suction nozzles
Combination nozzle (13)
The dual-purpose nozzle (13) is for vacuuming
solids and liquids over medium to large areas.
Anl_TH_VC_1930_SA_SPK7.indb 17
Anl_TH_VC_1930_SA_SPK7.indb 17
GB
6. Operation
6.1 ON/OFF switch (Fig. 2/2)
Switch position 0: Off
Switch position I: Normal mode
Switch position AUTO: Automatic mode
6.2 Dry vacuuming
For dry-vacuuming, use the pleated fi lter (15). In
addition, you can also fi t the dirt bag. (See point
5.2)
Always ensure that the fi lters are securely seated.
6.3 Wet vacuuming
For wet-vacuuming, use the foam fi lter (16) (see
point 5.2).
Check that the fi lter is securely seated at all times.
Water drain screw (Fig. 1)
To make the tank (8) easier to empty after wet va-
cuuming, it is fi tted with a water drain screw (19).
Open the water drain screw (19) by turning it anti-
clockwise and drain the liquid.
Caution!
When wet vacuuming, the fl oating safety switch
(5) closes when the maximum tank level is
reached. At the same time, the suction noise of
the equipment will change and become louder.
You must then switch off the equipment and em-
pty the tank.
Caution!
The wet and dry vacuum cleaner is not suitable
for the vacuuming of combustible liquids. For wet
vacuuming, use only the supplied foam fi lter.
6.4 Automatic mode
Connect the power cable of your electric tool to
the automatic socket-outlet (6) and connect the
suction hose (11) to the vacuuming connector of
your electric tool. Check that the connections are
secure and air-tight.
Set the switch (2) on the wet and dry vacuum
cleaner to position „AUTO" (automatic mode).
The moment you switch on the electric tool, the
wet and dry vacuum cleaner switches on as well.
When you switch off the electric tool, the wet and
dry vacuum cleaner switches off as well after a
pre-set delay.
- 17 -
17.12.12 13:57
17.12.12 13:57