Accessories - DeWalt DCS7485 Guide D'utilisation

Accessory Construction for Alternative Operation Methods
Narrow Rip Auxiliary Fence (Fig. AA–CC)
The narrow rip auxiliary fence should be used for a rip measuring 2" (51 mm) or narrower. This
fence will allow the guard to remain on the saw when completing narrow ripping. This fence will
provide ample space for proper use of a push block (
1. Follow the diagram in Fig. AA to construct the narrow rip auxiliary fence
NOTE: The length should be cut to fit the length
be parallel.
Fig. AA
1/2"
(12.7 mm)
3/8"
(9.5 mm)
1"
(25 mm)
2. After the narrow rip auxiliary fence is constructed, slip it over the saw table top and place it
flush to the fence as shown in Figure CC.
3. Feed the workpiece through until the edge of the material reaches the front edge of the saw
table top.
4. Continue feeding the material using the push block
Push Block (Fig. BB, CC)
IMPORTANT: Only use the push block 66
Rip Auxiliary Fence. The push block should be used once the material being cut reaches the saw
table top.
1. Construct a push block using the diagram in Figure BB.
NOTE: Edges
67 must be parrallel.
IMPORTANT: The over hanging edge
68
cause the push block to slip or push the material away from the fence.
Fig. BB
4-3/4"
5"
(121 mm)
(127 mm)
67
1/2"
12"
(12.7 mm)
(305 mm)
2-1/2"
(64 mm)
5-1/4"
1/2"
(133 mm)
(12.7 mm)
2. Place the push block 66 (Fig. CC) behind the material and ensure the lip of the block is flush
to the narrow rip auxiliary fence 69 .
3. Once the push block is in place, continue feeding the material until the cut is complete
making sure the push block remains flush to the narrow rip auxiliary fence at all times.
IMPORTANT: The narrow rip auxiliary fence and the over hanging edge
be the same thickness.
Fig. CC
12
, see Push Block).
66
69 .
64 of the saw table top and sides 65
64
4-3/4"
(121 mm)
65
3/8"
(9.5 mm)
66 until the cut is complete.
with the narrow rip auxiliary fence, refer to Narrow
Fig. BB) MUST be square. An uneven lip could
1/2"
(12.7 mm)
68 Fig. BB) should both
66
69
Featherboard Construction (Fig. DD, EE)
Featherboards are used to keep the work in contact with the fence and table, and help prevent
kickbacks. Dimensions for making a typical featherboard are shown in Figure DD. Make
the featherboard from a straight piece of wood that is free of knots and cracks. Clamp the
featherboard to the fence and table so that the leading edge of the featherboard will support the
workpiece until the cut is complete (Fig. EE). An 8" (203 mm) high flat board can be clamped to
the rip fence and the featherboard can be clamped to the 8" (203 mm) high board.
Fig. DD
must
The kerf should
be about 1/4"
4"
(6.4 mm) apart
(102 mm)

WARNING: Use featherboards for all non thru-sawing operations where the blade guard
assembly, anti-kickback assembly and riving knife cannot be used. Always replace the
blade guard assembly, anti-kickback assembly and riving knife when the non thru-
sawing operation is complete. Make sure the featherboard presses only on the portion of
the workpiece in front of the blade.
Fig. EE
MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn unit off and remove the
battery pack before making any adjustments or removing/installing attachments
or accessories. An accidental start-up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
66
performing this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.

Accessories


68
WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
Recommended accessories for use with your tool are available at extra cost from your local dealer
or authorized service center. If you need assistance in locating any accessory, please contact
D WALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1–800–4-D
e
(1–800–433–9258) or visit our website: www.dewalt.com.
• Compatible Stands (DWE74911)
• Metric rip scale (N458905)
• Dust extraction Y connector (contact your local dealer)
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (including brush inspection and replacement) should be performed by a
D WALT factory service center or a D
e
replacement parts.
24" (610 mm)
5" (127 mm)
WALT, have not been tested
e
WALT authorized service center. Always use identical
e
3/4"
(20 mm)
WALT
e