Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
OPERATING MANUAL FOR
FLOOR LUMINAIRE
WORKLIGHT LED SL-1 with Sensor
Read this short manual carefully and keep it accessible for further
reference!
SAFETY MESSAGES
Disregard of the safety messages may lead to danger of life, burning or
fire!
Installation, mounting or works on the electrical connection may only be
carried out by an approved electrician.
Type Y attachement: If the external flexible cable or cord of this luminaire is
damaged, it shall be exclusively replaced by the manufacturer or a
qualified electrician.
The product may not be modified or converted.
Do not hang or fasten anything on the product, especially no decoration.
Do not cover the product - provide free air circulation.
In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
A malfunction exists when:
visible damages appear.
the product does not work properly (e.g. flickering).
smoke, steam or crackling sounds appear.
smell of burning is recognisable.
an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
This product is not intended to be used by children. Ensure that children do
not suffer any harm e.g. by burns from hot surfaces or by electrical shock.
Additional safety messages are indicated by this symbol:
USE AS DIRECTED
This product serves exclusively lighting purposes and may:
only be used with a voltage of 220-240V ~50/60Hz.
only be installed according to safety class I (one).
only be operated on normally or not flammable surfaces.
only be used in dry condition,
not in damp or dirt-endangered rooms.
not in areas of high air humidity.
not be exposed to strong mechanical loads or to strong contamination.
PLACEMENT
Operate the product only on an even, stable and tilt-fixed background.
Choose a place where the installation is not a danger (e.g. stumbling,
knocking).
A minimum distance of 1,15 m should be kept to windows for an ideal daylight
control (fig. B).
INSTALLATION
It is recommended to assemble the product in a lying position.
Assemble the lamp base first (1).
Open the lamp head (2).
Do not place the lamp head in a way that the sensor lies on the ground.
Place the lamp head on the lamp pole. Secure it with the supplied screws
(3).
Connect the plugs of the lamp head with the sockets from the lamp pole
(4). Put these connections into the lamp head.
Close the lamp head (5).
Put up the luminaire. Note the directions for the place where the product is
operated!
Sensor Adjustment
Basic Adjustment:
I : Operation just with motion detection (The area
that is covered by the motion detector is depicted
in fig. A)
II: Operation with motion detection and daylight
sensor.
Switch off delay (1- 30 Minutes):
15
Adjustment of the time period after which the
15
1
30
luminaire switches off after the last detected
1
30
motion.
Daylight sensor (only active with Basic Adjustment
II):
On this the brightness which should be provided
on the illuminated surface is adjusted. The
adjusted brightness is controlled depending on the
ambient light. The brightness of the luminaire is
reduced when there is excess ambient light. The
brightness of the luminaire is increased when
there is less ambient light. This ensures that the
brightness on the illuminated surface is kept
constant. The area that is covered by the daylight
sensor is depicted in fig. C.
Button for burning-in fluorescent tubes (not
15
needed)
1
30
Adjustments on the Switch Box:
The switch „Prolong time" activates a prolonged switch-off period. After the lapse
of the switch-off delay time the brightness of the luminaire gets reduced to a
minimum for 15 resp. 30 minutes when activated.
On the switch „Mode" it is adjusted after which excess of the ambient light the
.
luminaire gets switched off. When set on "off" the luminaire gets switched off
when the adjusted brightness is exceeded by 150%. This value is 250% when
set on "on".
Overview of the Sensor- and Switch Box Adjustments
Prolong time
on off
Mode
on off
Daylight
sensor
= Off
Prolong
time
= 0 min.
Daylight
sensor
= On
Prolong
time
= 0 min.
Switch off of the luminaire when ambient light is exceeded
150%
on off
on off
on off
on off
on off
on off
Daylight
Daylight
Daylight
sensor
sensor
sensor
= Off
= Off
= Off
Prolong
Prolong
Prolong
time
time
time
= 30 min.
= 0 min.
= 30 min.
Daylight
Daylight
Daylight
sensor
sensor
sensor
= On
= On
= On
Prolong
Prolong
Prolong
time
time
time
= 15 min.
= 0 min.
= 15 min.
by
150%
250%
250%
OPERATION
Putting into service
Use only parts, which are supplied with the product or are described as
accessories!
Inspect the product for loose parts inside the housing. When there are
loose parts inside the housing and these are not explicitly described the
product may not be installed or operated.
Connect the plug of the product with a socket of the public power supply
(mains).
Using the switch the luminaire may be turned on and off and also be
dimmed.
Short push: on / off
Long push: dimming operation
MAINTANANCE AND CARE
Light source
Under regular usage the LED light source has an extraordinary long
lifetime. If nevertheless damage or failure occurs, contact your local dealer
to exchange the LED light source.
Care
Disconnect the product from the power supply and let it cool down, before
you clean the product.
Clean the product on a regular basis using a slightly moistened, soft and
fluff-free cloth. Please also note additional supplied notes on maintanance
and care.
STORAGE AND DISPOSAL
Storage
The product must be stored in a dry and clean environment. Do not
strain the product mechanically during storage.
After a damp or soiling storage the product may only be installed
after checking its condition by an approved electrician.
Disposal (European Union)
Do not dispose the product with the regular household waste! Products
marked with this sign must be disposed according to the directive(WEEE,
2012/19) on electrical and electronic devices at local collection points for
such devices!
art.-no. 157911 / 157915 © 21.03.2018 SLV GmbH,
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany,
Tel. +49 (0)2451 4833-0
Technical Details are subject to change.
Publicité
