Publicité
Les langues disponibles
Les langues disponibles
When operating with the Multi-Train
System, you can remotely control the
loco's functions. Press the lighting
button ("9" with remotes) to turn the
loco lights on or off.
When operating with the Multi-Train
System, the loco features a "Back-
EMF" function. This keeps the motor
speed constant (and under normal
conditions the loco speed), even
when the load of the loco changes,
for example, in curves or on grades.
This feature does not work at top
speed, because additional voltage
must be available to overcome any
added load.
If desired, numerous functions of the
onboard decoder, such as accelera-
tion, braking, direction of travel and
many others, can be programmed
using a PC and the 55045 MTS PC
Decoder Programming Module (see
Instructions for advanced users).
These functions also can be pro-
grammed from the 55015 Universal
Remote.
Lighting
This model features directional light-
ing: Three white front and two red
rear lights. The model has a "flat"
multi-purpose socket, with a remov-
able cover, one on each end wall (Fig.
3). These sockets can be used to
provide track power to LGB cars with
lighting or sound electronics.
To remove the cover of a socket, pull
it straight out. If the cover is tight,
gently use a small straight screw-
driver to pry it out. (Do not pull out
the rectangular outer housing.)
Power Supply
Attention! For safety and reliability,
operate this model with LGB power
supplies (transformers, power packs
and controls) only. The use of non-
LGB power supplies will void your
warranty.
12
Use this model with LGB power sup-
plies with an output of at least 1
amp. For more information on LGB
power supplies for indoor, outdoor
and multi-train operation, see the
LGB catalog.
Catenary Power Operation
This locomotive can be operated with
a powered catenary system (see
Operating Modes). The bottom of
this model is marked with a red dot.
Place the model on the track with the
red dot pointing to the rail that is not
connected to the catenary power
supply (Fig. 4).
Hint: To operate multiple trains on
the same track, we recommend the
LGB Multi-Train System (see Multi-
Train System). With the Multi-Train
System, you can use an unpowered
catenary system for prototypical
appearance.
CAUTION! This model may be pow-
ered with a catenary on analog lay-
outs only. For operation with the dig-
ital Multi-Train System, the model
must use track power. Otherwise,
dangerously high voltages may
result.
Attention! After extended operation,
this model may leave carbon dust or
other debris around the track. This
dust and debris can stain carpet and
other materials. Consider this when
setting up your layout. Ernst Paul
Lehmann Patentwerk and LGB of
America are not liable for any dam-
ages.
SERVICE
Do-It-Yourself Service Levels
Level
- Beginner
Level
- Intermediate
Level
- Advanced
Attention! Improper service will void
your warranty. For quality service,
contact your authorized retailer or an
LGB factory service station (see
Authorized Service).
Hint: Additional expert instructions
for many LGB products are available
at www.lgb.com.
Lubrication
The axle bearings should be lubricat-
ed occasionally with a small amount
of LGB Maintenance Oil (50019).
Cleaning
This model can be cleaned externally
using a mild detergent and gentle
stream of water. Do not immerse this
model.
Replacing the light bulbs
Lower lights: Remove the ring
around the lantern lens. Carefully pry
the lens away from the lantern. Using
tweezers, remove and replace the
bulb. Reassemble.
Upper lights: Carefully pry the lens
away from the lantern. Using tweez-
ers, remove and replace the bulb.
Reassemble.
Cab light: Using tweezers, remove
and replace the bulb. If you have dif-
ficulties reaching the light bulb,
remove the four screws holding the
roof and remove the roof to access
the light bulb.
Replacing the traction tire
- Remove the screw on the drive
wheel with the traction tire.
- Remove the side rod from the drive
wheel.
- Use a small, straight-blade screw-
driver to replace the traction tire:
- Pry the old traction tire out of the
wheel groove.
- Gently insert the new traction tire
into the wheel groove.
- Make sure that the traction tire is
seated properly in the wheel
groove.
- Reassemble.
Maintenance parts
50010 Smoke and Cleaning Fluid
50019 Maintenance Oil
51020 Gear Lubricant
62204 Standard Motor with Long
Shaft
63120 Brushes, Assembled,
14 mm and 16 mm,
8 pieces
63218 Standard Pick-Up Shoes,
2 pieces
63403 Scissor Pantograph, Silver
68511 Plug-In Bulb, Clear, 5V,
10 pieces
69184 Traction Tire, 46.5mm,
10 pieces
INSTRUCTIONS FOR ADVANCED
USERS
MTS Onboard Decoder
Programming functions
You can program numerous func-
tions of the onboard decoder to suit
your requirements. If you want to do
this, program the "function values"
in "registers" (CVs) using a PC and
the
55045
MTS
PC
Decoder
Programming Module. You can also
program the function values using a
55015 Universal Remote.
Hints:
- For normal operation, it is not nec-
essary to change the function val-
ues.
- If programming results in unsatis-
factory operation, you can repro-
gram the factory pre-set values of
most important CVs: Program reg-
ister CV55 to function value 55.
13
Publicité
