Preparing For Installation - M-E VISTUS VD Mode D'emploi

PREPARING FOR INSTALLATION

The following lines are required:
Single-family house: 4 lines from the outdoor unit to the indoor unit
and 2 lines from the outdoor unit to the door opener.
Two-family house: Here 4 lines are required per bell button from the
outdoor unit into each residential unit. 4 lines for family 1 and 4 lines
for family 2, as well as 2 lines to the door opener.
NOTES:
1. A wiring plan can be found in the affix.
2. With the VISTUS-System you can also combined video
and audio components.
Up to four indoor units can be connected in parallel per residential unit.
The connection can be laid as
1. Serial connections (from indoor station to indoor station) or as
2. Radial connections (parallel) from one central point
(distribution box).
The wiring plan in the affix is base on a radial wiring
system as this is preferable.
The lines should be laid in such a way that each is fed out of the wall
directly behind the corresponding outdoor/indoor unit.
ASSEMBLY OF THE OUTDOOR STATION
The door intercom point is designed for surface mounting.
Preparation
The camera should be fitted at a height of approximately 1.5 m -1.6
m (from the centre of the camera) (Figure A). Before assembling the
door intercom you should test whether the camera shows enough of
a visitor. Adjust the assembly height and assembly location to your
circumstances as necessary.
1. Remove the two screws (5) in order to be able to open the casing
on the outdoor station. The casing is also fitted with notches and
projections that connect the upper and lower parts of the casing.
Thus a certain amount of force is necessary in order to separate the
casing parts.
2. Position the drilling template for the outdoor station in a level
location at the intended assembly location (a spirit level is helpful
for this) and attach it with sticky tape.
3. Use the drilling template to drill the attachment holes with a 6mm
drill and insert a dowel into each hole.
VISTUS VD-600_I-Manual_210x240_Fin24.indd 15
4. Now remove the drilling template.
5. Feed the lines through the large hole in the outdoor station and
secure them with 4 screws.
6. Connect the line in accordance with the wiring plan.
7. Attach the front cover and connect the microphone and loudspeaker
cables to the board according to the numbering (1 for microphone, 2
for loudspeaker, 3 for camera).
8. Screw the front cover on using both casing screws (5). Please ensure
that the screws are not tilted as this can damage the thread in the
lower section of the casing.
Customize the nameplates*
The nameplate covers can simply be levered off to the front with a slotted
screwdriver, as shown in the side view illustration. Insert an appropriately
labelled foil or paper and replace the nameplate cover. Replace the
nameplate cover and push it into the case with a little force until it clicks
into place.
* Size of the nameplate:
VISTUS VD 6X10: 71 mm x 50 mm
VISTUS VD 6X20: 71 mm x 25 mm
ASSEMBLY OF THE INDOOR STATION
The installation height of the Indoor stations can be selected freely
according to your circumstances.
1. The casing on the 3.5" indoor station is kept together with notches
and projections. To separate the lower section from the front section,
press a small slotted screwdriver against the snap fastener (B.15) on
the bottom side. The 7" indoor station is kept together by 2 casing
screws (C.15).
2. Use the lower section of the casing as an aid to mark the drill holes.
Make sure that you hold the lower section in a horizontal position for
this step.
NOTE: The lower casing section on the 3.5" indoor station can also be
attached to a hollow wall box. The corresponding attachment holes
are located around the line feed hole. If this does not provide enough
hold then drill more holes and use them to also screw the indoor
station in place.
3. Drill the attachment holes with a 6 mm drill and insert one dowel in
each hole.
4. Feed the lines through the feed hole in the lower casing part designed
for this purpose and screw this down.
5. Attach the lines in accordance with the wiring plan and replace the
front casing section onto the lower casing section. Make sure that it
clicks correctly into place.
15
ENGLISH | VISTUS-VD
(3.5" AND 7")
10.12.19 14:24