Electric Shock Hazard; Fire Hazard; Important Safety Information - Hatco HWBI Série Manuel D'installation

English
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
WARNING

ELECTRIC SHOCK HAZARD:

• Turn power switch OFF, disconnect unit from power
source, and allow unit to cool before performing any
maintenance or cleaning.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• Remote control enclosure must be mounted on vertical
wall and installed in vertical position. Mounting remote
control enclosure in horizontal position may result in
collection of liquids and lead to electric shock.
• Operating voltage of remote control enclosure water valve
exceeds 50 V (extra low voltage). Enclosure is marked
with the following hazard identification symbol:
• DO NOT use unit to melt or hold ice. Doing so may
cause condensation, creating an electrical hazard and
causing personal injury and/or damage to unit. Damage
caused by condensation is not covered by warranty.
• For non auto-fill units, turn off unit when filling with
water and avoid splashing.
• Do not clean unit when it is energized or hot.
• This unit is not "jet-proof" construction. Do not use
jet-clean spray to clean this unit.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.

FIRE HAZARD:

• Install unit with a minimum of 3-1/2" (89 mm) of space
from bottom of unit to all combustible surfaces to
prevent combustion.
• Unit must be installed using ribbon putty gasket
between the unit and the installation surface per
installation instructions (refer to the INSTALLATION
section of this manual).
• Do not use flammable cleaning solutions to clean this
unit.
This unit must be installed by qualified, trained installers.
Installation must conform to all local electrical and
plumbing codes. Check with local plumbing and electrical
inspectors for proper procedures and codes.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them
away from unit.
Form No. HWBIM-0820

IMPORTANT SAFETY INFORMATION

Make sure all operators have been instructed on the safe
and proper use of unit.
Make sure food product has been heated to the proper
food-safe temperature before placing in the unit. Failure
to heat food product properly may result in serious health
risks. This unit is for holding pre-heated food product only.
Hatco Corporation is not responsible for actual food
product serving temperature. It is the responsibility of the
user to ensure that food product is held and served at a
safe temperature.
This unit has no "user-serviceable" parts. If service is required
on this unit, contact an Authorized Hatco Service Agent or
contact the Hatco Service Department at 800-558-0607 or
414-671-6350.
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Drain water may reach temperatures in excess of 200°F
(93°C). Use appropriate plumbing materials when
installing drain.
• DO NOT clean unit while it contains any food product.
Remove food product and allow unit to cool completely
before cleaning.
Locate unit at proper counter height in an area that is
convenient for use. The location should be strong enough
to support the weight of unit and contents.
Auto-Fill units must be installed with adequate backflow
protection and must conform with all federal, state, and
local codes.
Auto-fill units supplied with water from a reverse osmosis
(RO) system (or similiar water filtration system) must be
installed with an operating reminerialization sytem to
ensure proper operation. Failure to do so may cause unit to
overfill. Damage caused by overfilling is not covered under
warranty.
Units are voltage-specific. Refer to specification label for
electrical requirements before beginning installation.
Standard and approved manufacturing oils may smoke up
to 30 minutes during initial startup. This is a temporary
condition. Operate unit without food product until smoke
dissipates.
Do not locate unit in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures could cause damage to unit.
Unit is designed and recommended for use in or on
metallic countertops. Damage to any countertop material
is not covered under the Hatco warranty. For other
surfaces, verify with manufacturer that material is suitable
for prolonged temperatures up to 200°F (93°C).
3
WARNING
CAUTION
NOTICE