Maintenance And Cleaning; Lubrication; Technical Data - Makita HG6530V Manuel D'instruction

Stripping paint
Mount an appropriate accessory.
Q
Set a high air temperature.
Q
Switch the tool on.
Q
Direct the hot air onto the paint to be removed.
Q
When the paint softens, scrape the paint away
Q
using a hand scraper.
Do not strip metal window frames, as
the heat may be conducted onto the
glass and crack it. When stripping
other window frames, use the glass
protection nozzle.
Do not keep the tool directed at one
spot too long to prevent igniting the
surface.
Avoid collecting paint on the scraper
accessory, as it may ignite. If neces-
sary, carefully remove paint debris
from the scraper accessory using a
knife.
Stationary use
This tool can also be used in stationary mode.
Place the tool onto a stable workbench.
Q
Secure the cable to prevent pulling the tool off the
Q
workbench.
Carefully switch the tool on.
Q
Make sure that the nozzle always
points away from you and any
bystanders.
Make sure not to drop anything into
the nozzle.
Cooling down
The nozzle and accessory become very hot during use.
Let them cool down before attempting to move or store
the tool.
To reduce the cooling time, switch the tool on at
Q
the lowest air temperature setting and let it run for
a few minutes.
Switch the tool off and let it cool down for at least
Q
30 minutes. Always place it vertical and standing.
When the inside of heat gun gets too
hot, the indication on the LCD blinks.
In that case, set the slide switch to
position 1 to cool down the tool.
After cooling down fully, restart the
operation.
If the LCD still blinks after the restart,
contact your local Makita Service
Center.

MAINTENANCE AND CLEANING

Attention:
work on the equipment, pull the
power plug.
Before performing any
Maintenance
Your Power Tool has been designed to operate
Q
over a long period of time with a minimum of
maintenance. Continuous satisfactory opera-
tion depends upon proper tool care and regular
cleaning.

Lubrication

Your power tool requires no additional lubrication.
Q
Cleaning
To prevent overheating of the motor, keep the
Q
ventilation slots of the machine clean and free
from dust and dirt.
Regularly clean the machine housing with a soft
Q
cloth, preferably after each use. If the dirt does not
come off use a soft cloth moistened with soapy
water.
Never use solvents such as petrol,
alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.

TECHNICAL DATA

Model No:
HG6531C
Voltage 220-240V~50Hz
Power
2000W
Temperature I 50°C
II 50-650°C
Air flow
I 200-550L/M
II 200-550L/M
Overall length 257mm
Net weight
0.71kg
* NOTE: 650°C can be achieved only with the wide-slot nozzle,
overlap welding nozzle or welding nozzle.
Default setting of the preset mode
No. Application name
1 FREE SET 1
2 FREE SET 2
3 SCRINKING
4 FORMING
5 SOLDERING COPPER
6 DRYING PAINT
7 PAINT STRIPPING
8 WELDING FLOOR FOIL
9 WELDING PPEPDM
10 WELDING HDPE
11 WELDING PP
12 WELDING PVC-U
13 WELDING ABS
14 WELDING PC
8 English
HG6530V
110V~50Hz 220-240V~50Hz
1400W 2000W
I 50°C I 50°C I 50°C
II 50-650°C*
II 50-650°C* II 50-650°C
III 50-650°C III 50-650°C*
I 400L/M
I 150-450L/M I 500L/M
II 150-450L/M II 280L/M II 230L/M
III 550L/M
257mm
0.72kg
Temperature Air volume
250°C
500°C
300°C
250°C
650°C
650°C
450°C
450°C
280°C
300°C
320°C
340°C
360°C
380°C
110V~50Hz
1400W
III 450L/M
5
5
3
4
3
5
5
3
3
3
3
3
3
3