Maintenance And Cleaning; Technical Data - Makita HG5030 Manuel D'instruction

Stationary use
This tool can also be used in stationary mode.
Place the tool onto a stable workbench.
Q
Secure the cable to prevent pulling the tool off the
Q
workbench.
Carefully switch the tool on.
Q
Make sure that the nozzle always
points away from you and any
bystanders.
Make sure not to drop anything onto
the nozzle.
Cooling down
The nozzle and accessory become very hot during use.
Let them cool down before attempting to move or store
the tool.
To reduce the cooling time, switch the tool on at
Q
the lowest air temperature setting and let it run for
a few minutes.
Switch the tool off and let it cool down for at least
Q
30 minutes. Always place it vertical and standing.

MAINTENANCE AND CLEANING

Attention! Before performing any
work on the equipment, pull the
power plug.
Maintenance
Your Power Tool has been designed to operate
Q
over a long period of time with a minimum of
maintenance. Continuous satisfactory opera-
tion depends upon proper tool care and regular
cleaning.
Lubrication
Your power tool requires no additional lubrication.
Q
Cleaning
Keep the ventilation slots clear and regularly clean
Q
the housing with a soft cloth.
Cleaning
Keep the ventilation slots of the machine clean to
Q
prevent overheating of the motor.
Regularly clean the machine housing with a soft
Q
cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
Q
If the dirt does not come off use a soft cloth moist-
Q
ened with soapy water.
Never use solvents such as petrol,
alcohol, ammonia water, etc. These
solvents may damage the plastic
parts.

TECHNICAL DATA

Model No: HG5030
Voltage: 120V
Frequency: 60Hz
Current: 13.0A
Setting: I II
Temperature:[°C] 400°C 550°C 50-350
[°F] 752 1022 122-662 176-1022 122 662 1022
Setting: I II
Air flow: [L/M] 200 400
[CFM] 7 14
MAKITA LIMITED ONE YEAR
WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested
before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period
of ONE YEAR from the date of original purchase.
Should any trouble develop during this one year period,
return the COMPLETE tool, freight prepaid, to one
of Makita's Factory or Authorized Service Centers. If
inspection shows the trouble is caused by defective
workmanship or material, Makita will repair (or at our
option, replace) without charge.
This Warranty does not apply where:
• repairs have been made or attempted by others:
• repairs are required because of normal wear and
tear:
• the tool has been abused, misused or improperly
maintained:
• alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE
PRODUCT. THIS DISCLAIMER APPLIES BOTH
DURING AND AFTER THE TERM OF THIS
WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED
WARRANTIES, INCLUDING IMPLIED WARRANTIES
OF "MERCHANTABILITY" AND "FITNESS FOR A
SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM
OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state. Some states do not allow the exclusion or lim-
itation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
Some states do not allow limitation on how long an
implied warranty lasts, so the above limitation may not
apply to you.
Subject to change without notice.
5 English
HG6031V HG6030
120V 120V
60Hz 60Hz
13.0A 13.0A
I II I II III
80-550 50 350 550
I II I II III
200 400 200 200 400
7 14 7 7 14