Cloer 5609 Notice D'utilisation page 13

·
Close the water tank lid.
·
Open the pivot filter, insert a 1x4 paper filter and
add the required amount of coffee powder.
·
Close the pivot filter again.
·
Place the carafe on the warming plate. Make
sure that the carafe and its lid is properly placed
under the funnel of the filter basket to ensure that
coffee runs down from the filter into the carafe.
·
Press the ON/OFF button
·
During the brewing process, the drop symbol
flashes in the display.
·
The tank lighting switches off once all the coffee
has come through.
·
The drip-stop function allows you to remove the
carafe to pour yourself a cup of coffee before
the brewing cycle ends. In this case, you need
to make sure you put the carafe back in its place
in 30 seconds to prevent over-bubbling of water
or coffee.
·
After the brewing process, the filter coffee
maker keeps the coffee hot for 30 minutes, and
then switches off automatically. During this
time, the display flashes on the cup icon
the elapsed warm-keeping time is displayed
instead of the time.
·
If you want to switch off the unit manually,
please press 1x the ON/OFF button
CAUTION! Allow the unit to cool
down immediately before the
next use. Otherwise, the fresh
water you poured in may
overheat and release steam.
Risk of scalding!
Energy-saving and environment-friendly:
Flexible "keep warm" time
·
A new regulation of EU Requirements (No.
801/2013) means that filter coffee makers with
"keep warm" plate may protect the environment
by having only a "keep warm" time of 30 minutes
beginning in 2015.
·
In parallel his saves your energy costs!
·
We want to lead by example, so we reduced the
"keep warm" time to 30 minutes for your filter
coffee maker 5609 in 2013 already.
·
But we also know that sometimes this is not
enough!
·
So that you can remain flexible, your filter coffee
maker 5609 provides the option to change the
"keep warm" time of coffee to 1 hour, 1 ½ hours
or 2 hours arbitrarily. The default setting of 30
minutes can be set back at all times.
·
Of course you can cancel every warming time
before the time passed by while pressing the
ON/OFF switch .
·
The display shows the warming periods as follows:
00:30 (= ½ hour)
01:00 (= 1 hour)
01:30 (= 1 ½ hours)
02:00 (= 2 hours)
.
and
.
·
Note: To change the "keep warm" time the
device must always be disconnected from the
outlet first and reconnected again.
To change the "keep warm" time, please
proceed as follows:
·
Insert the power plug into the wall socket.
·
The time 00:00 is flashing.
·
Now please press AUTO, the arrow up button
and SET at the same time.
AUTO
·
Now the display shows the "keep warm" time
00:30 (or, if ever changed, the current "keep
warm" time), as well as the clock and the cup
symbol.
WENN NICHT ANDERS DEFINIERT: OBERFLÄCHENGÜTE:
BEMASSUNGEN SIND IN MILLIMETER
OBERFLÄCHENBESCHAFFENHEIT:
TOLERANZEN:
LINEAR:
WINKEL:
NAME SIGNATUR DATUM
·
GEZEICHNET Use the arrow keys (
GEPRÜFT
GENEHMIGT of the "keep warm" times (00:30, 01:00, 01:30 or
PRODUKTION
WERKSTOFF:
QUALITÄT
02:00).
·
Then press SET to confirm the desired "keep
GEWICHT:
warm" time.
·
After this, the display switches back to the time
00:00. Please continue as described in the in the
instruction booklet under "Setting the time".
·
Note: The set "keep warm" time is saved even if
the unit is disconnected from the power supply
and can be changed at any time by repeating
the above steps.
Setting an automatic start time
·
Your Cloer filter coffee maker is equipped with
an automatic start time function.
·
Note: It only works when the tank insert for
temperature stabilization (see page 3) is seated
in place.
·
This means you can set a time your coffee maker
should start making coffee in your absence (for
example, before you get up in the morning).
·
Press 1x SET to do so.
·
The timer symbol (= clock
the hour of 0:00 flashes.
·
Use the arrow keys
hour and press SET.
·
When the display switches to minutes, use the
arrow keys to adjust the minutes.
·
Press SET again. The automatic start time is now
set.
·
Fill in the required amount of water and coffee
powder.
·
Now press AUTO to activate the start time.
·
The timer symbol (= clock
SET
ENTGRATEN
ZEICHNUNG NICHT SKALIEREN
ÄNDERUNG
UND SCHARFE
KANTEN
BRECHEN
BENENNUNG:
or ) to choose one
BASE(Default)
ZEICHNUNGSNR.
MASSSTAB:1:1 BLATT 1 VON 1
) is displayed and
to adjust the required
) is displayed to
EN
A3
13