Coffee Preparation - Cloer 5609 Notice D'utilisation

Introduction
Dear Customer,
by buying the Cloer filter coffee maker you
have decided on a quality product complying
with the most modern development standard
regarding technology and functionality.
EN
Make sure you acquaint yourself with the
appliance before and read the operating
instructions carefully.
We wish you pleasure with your new filter coffee
maker.
Setting up
·
Remove all packaging parts and, if applicable,
stickers, not the rating label.
·
Place the filter coffee maker on a dry, non-slip
and even surface.
Before using the first time
·
Read these instructions carefully before first
use.
·
Prior to brewing coffee for the first time, run
the coffee maker with water only for one or two
times (omitting coffee powder and paper filter).
·
Open the lid of the water tank and fill in cold
water to the 12-cups marking by using the glass
carafe.
·
Place the carafe on the warming plate and press
the ON/OFF button to switch on the appliance.
·
Switch off the coffee maker after the brewing
process and pour away the water.
Safety instructions for operation
The appliance meets the
requirements of the applicable
EC directives.
The appliance is intended for
in door use only.
·
Use the coffee maker exclusively for making
coffee. Do not fill other liquids or foodstuffs in
the coffee maker.
·
Fill the water tank with cold water only.
·
Never operate the appliance without water.
·
Do not immerse the coffee maker in water or
any other liquid!
·
ATTENTION: When filling the water tank with
water, avoid the maximum cup marking being
exceeded. A possible bubbling over can cause
a danger of scald!
·
During use, never open the lid of the water
tank.
ATTENTION!
Always unglug appliance
when not in use!
Setting the time
·
Prior to starting the very first brewing process
12
or disconnecting the unit from the mains, you
should set time on the display.
·
Insert the plug in the power socket.
·
The number of hours appears on the screen.
·
You may also use the arrow keys
the hour and then press SET.
·
The display changes to the minutes, which you
can re-adjust using the arrow keys.
·
Press SET again, when you are finished.
·
The time is now set.
·
If you wish to change the time again (e.g. for
summer / winter time), long press the SET
button and proceed as described above.
·
Info: If you wish to set the clock to American
time (AM / PM), press and hold SET ca. 2 sec.
to enter the setting mode, and then press the
two arrow keys simultaneously. The display will
change to American time. Now press SET 2x to
complete the process.
Temperature stabilization
Your coffee maker is equipped with a unique
temperature stabilization unit, which ensures
constant brewing temperature and thus the
best coffee results without bitter aftertaste.
This is ensured by the float below the insert
inside the tank. It always allows only small
amounts of water run through the heating
system to achieve
temperature and get the most from your coffee
powder. Coffee can develop its best flavor only if
you ensure the right brewing temperature.

Coffee preparation

·
Plug cord into a standard electrical outlet.
·
Open the lid of the water tank.
·
Use the glass carafe to fill the water tank with
fresh cold water. Check the left scale of the tank
if you do not use BRITA ®MAXTRA® water filter
cartridge or the right scale of the tank, if you use
it (see page 11).
·
If you like to use coffee maker without BRITA®
MAXTRA® water filter cartridge please remove
the tube (see below) out of the water tank.
·
Notice: If you use the coffee maker without the
tank insert, use the glass carafe to fill in water
and do not exceed the maximum capacity of
the carafe, otherwise water may bubble over
during the brewing process.
·
Once you have filled the tank, the lighting lights
on indicating operational readiness. Unless you
press the ON/OFF button, otherwise, after 30
seconds, the tank lamp switches off again.
·
Never fill the tank with water above the
maximum level.
·
Note: Make sure that the tank insert (with
the float and the BRITA®filter device) is
correctly installed to ensure that the rubber
seal fits properly.
to adjust
optimum brewing