Quick Menu; Battery Charge Indicator - Bosch Kiox BUI330 Notice D'utilisation D'origine

language. You can reset the Kiox to its factory settings,
run a software update (if available) and choose between a
black or white design.
– <Information> – Information about your Kiox
Information on FAQ (frequently asked questions), certi-
fication, contact information, information on licences.
You can find a detailed description of each parameter in the
online operating instructions at
www.Bosch-eBike.com/Kiox-manual.

Quick menu

Selected settings are displayed on the quick menu. These
settings can also be changed while riding.
You can access the quick menu via the select button (9). It
cannot be accessed from the status page.
The following settings can be changed via the quick menu:
– <Res. trp data Last (Reset trip data Last:
[DD.Mon.YYYY HH:MM])>
All data on the journey so far is reset to zero.
– <eShift>
You can use this to adjust the cadence or the starting
gear, for example. The starting gear can be adjusted in
the settings under <My eBike> → <eShift>.
Switching the on-board computer on/off
To switch on the on-board computer, briefly press the on/
off button (4).
To switch off the on-board computer, press and hold the
on/off button (4) for more than one second.

Battery charge indicator

The battery charge indicator of the eBike battery d can be
read on the status page and the status bar. The eBike bat-
tery's state of charge is also indicated by the LEDs on the
eBike battery itself.
Colour of the Explanation
indicator d
White The eBike battery is over 20 % charged.
Yellow The eBike battery is over 5 % charged.
Red The capacity for assisting the drive has been
used up, and assistance is switched off. The
remaining capacity will be provided for the
bike lights and the on-board computer. The
remaining capacity of the eBike battery is
enough for about 2 hours of lighting. This
does not account for other consumers (e.g.
eShift gear changing, charging external
devices using the USB port) which could re-
duce the duration.
If the eBike battery is being charged on the wheel, a corres-
ponding notification will be displayed.
If the on-board computer is removed from the holder (5),
the state of charge that was last displayed for the battery is
saved.
Bosch eBike Systems
Setting the assistance level
On the operating unit (7), you can set the level of assistance
you want the eBike drive to provide you with while pedalling.
The assistance level can be changed at any time, even while
cycling.
Note: In some models, the assistance level may be preset
and cannot be changed. There may also be fewer assistance
levels available than stated here.
If the manufacturer has configured the eBike with eMTB
Mode, the assistance level SPORT is replaced by eMTB. In
eMTB Mode, the assistance factor and torque are dynamic-
ally adjusted according to the force you exert on the pedals.
eMTB Mode is only available for Performance Line CX
drives.
The following assistance levels are available as a maximum:
– OFF: Motor assistance is switched off. The eBike can just
be moved by pedalling, as with a normal bicycle. The
push assistance cannot be activated at this assistance
level.
– ECO: Effective assistance with maximum efficiency, for
maximum range
– TOUR: Steady assistance, long range for touring
– SPORT/eMTB:
SPORT: Powerful assistance, for mountain biking and for
cycling in urban traffic
eMTB: Optimum assistance whatever the terrain, rapid
acceleration when starting from a standstill, improved dy-
namics and top performance
– TURBO: Maximum assistance even at high pedalling
speeds, for biking sports
To increase the assistance level, press the + (12) button on
the operating unit repeatedly until the desired assistance
level appears on the display. To decrease the assistance
level, press the – (11) button.
The requested motor output appears on the display h. The
maximum motor output depends on the selected assistance
level.
If the on-board computer is removed from the holder (5),
the assistance level that was last displayed for the battery is
saved.
Switching the push-assistance function on/off
The push assistance aids you when pushing your eBike. The
speed in this function depends on the selected gear and can
reach a maximum of 6 km/h. The lower the selected gear,
the lower the speed of the push assistance function (at full
power).
The push assistance function must only be used when
u
pushing the eBike. There is a risk of injury if the wheels
of the eBike are not in contact with the ground while using
the push assistance.
To activate the push-assistance function, briefly press the
(13) button on your on-board computer. Once it is activ-
ated, press and hold the + button within 3 s. The eBike drive
is now switched on.
English – ​ 5
1 270 020 XBK | (17.05.2018)