SFA SANI COMPACT Star Notice D'installation page 9

8
MOUNTING THE PAN AND
CUTTING OUT THE FASCIA
PANEL
1 - Offer up the fascia panel (not provided) to
the support frame which has been fixed to
the wall.
2 - Locate the panel exactly to the support
frame.
3
- Drill 2 holes (25mm) through the fascia
panel to correspond with the threaded rods
on which the pan will hang.
4
- Offer up the template
E
fascia, positioning the holes for the WC
support rods accordingly.
5 - Trace the inner shape of the template onto
the fascia.
6 - Remove the template
E
fascia as traced.
7
- Make any finishes to the support wall and
fix on the fascia panel.
8 - Note: If you are tiling the wall, the tiles will
have to be cut out in the same way as the
fascia panel.
9
CONNECTIONS
WARNING: Before making the various
connections, check the following:
1 - Ensure that the threaded rods are
correctly spaced and the dimensions in
drawing 7a adhered to, otherwise the
screw covers will not fit.
2 - Put the template in place onto the
E
threaded rods.
CONNECTION OF WASH HAND BASIN
9a
1 - Saw off the tip of the inlet spigot.
De-burr it.
2 - Connect the rubber waste connection
to the spigot with the correct clip
I
and crimp it with pincher pliers.
3 - Connect the other end of the connector
to the 40 mm end of washbasin
I
waste pipe and secure it with clip
DISCHARGE CONNECTION
9b
1 - Slide tube onto the discharge
F
connector.
2 - Fix the non-return valve
to the discharge pipe.
3 - WARNING: The non-return valve must
be installed vertically with the arrow
pointing upwards.
4 - Stretch the connector and fix the end to
the non-return valve using clip
9c CONNECTION OF THE WATER SUPPLY
Connect the water supply pipe to the water
inlet pipe (male to female iron connection).
1 0
MOUNTING THE PAN
Once the connections have been made,
1 - Fit the clear tubes onto the threaded
D
rods.
2 - Set the pan onto the threaded rods
without tightening the nuts.
1 1
NORM
1 2
COMMISSIONING THE UNIT
1 - Open the isolation valve to allow inflow of
water. Presss the button on the back of the
pan to start the flushing cycle. Throw a few
pieces of paper into the pan and flush.
2 - Turn on the washbasin tap. The unit
should activate automatically.
3 - Demount the pan and check the wa ter
to the support wall
tightness of all connections.
4 - WARNING:
cause the unit to activate automatically.
and cut out the
1 3
COMPLETING
THE INSTALLATION
1 - Remount the pan onto the threaded
rods.
2 - Fit the white UPVC washers
threaded rods and tighten the nuts
Then fit the nut covers
3 - Cut away any protruding lip of the
template around the pan contour.
4 - Seal the pan/wall joint with silicon.
1 4
USAGE
1 - A WC fitted with a SANICOMPACT
SANICERAMIC 3
not require any special maintenance.
2 - WARNING:
SANICERAMIC 3
be used for the evacuating of
J
normal human waste, toilet paper and
household WC cleansers.
Damage may occur to the machine if
the following are disposed of via the
.
WC; Cotton wool, tampons, sanitary
K
towels, wet wipes, kitchen towels,
condoms as well as other fabric or
hard objects. Solvents, acids and
other chemicals can also cause
damage to the unit, and will
invalidate the warranty.
with clip 3 - WARNING:
G H
not to be used for a prolonged time the
water supply to the bathroom is turned
off.
4 - This device is not designed for
persons (including children) with
limited physical, sensory or mental
.
H
abilities, or those with minimal
experience and knowledge, unless
they are monitored and are given
the necessary instructions for using
the device, with the help of a person
responsible for their safety. Monitor
children and make sure they do not
play with the device.
Any dripping of the taps will
onto the
L
.
B
.
M
Star /
®
pump/macerator does
®
Star /
The SANICOMPACT
®
range should only
®
In the event that the unit is
9
1 5
CARE OF YOUR
SANICOMPACT ® STAR/SANICE-
RAMIC 3 ®
• Normal household bleaches/WC cleansers
can be used with a SANICOMPACT
SANICERAMIC 3
®
• To avoid the build up of limescale in the unit,
use the following procedure.
- disconnect the power supply to the unit,
- pour 3 or 4 litres of water mixed with a
strong solution of descalent/spirit of salts
into the WC pan,
- leave it to stand for 1 or 2 hours, then
re-connect the electric supply,
- flush several times to clear.
The frequency of this operation will depend on
the hardness of the water in your locality. We
would recommend this be done about twice a
year.
1 6
AFTER SALES SERVICE
In the unlikely event of a failure or
malfunction, please call our after sales
service department. You will be directed to
your nearest registered service engineer.
WARNING: Always disconnect the electricity
supply before attempting any work on the
Star /SANICERAMIC 3
SANICOMPACT
®
1 7
GUARANTEE
Star /SANICERAMIC 3
The SANICOMPACT
®
range is guaranteed for 2 years, subject to
correct installation and usage.
Star /
®
.
®
®