IKRA ART 4030 Manuel D'utilisation page 17

A replacement spool may be stored in a removable com-
partment on the grip housing (fig. 12).
To remove the compartment cover, pull firmly on the
marked positions. After the spool has been removed,
replace the cover firmly.
Adjusting the mowing string
• Whenever the mowing performance decreases, it is
necessary to adjust (to extend) the mowing string.
• Turn the mowing machine on and hold it above the grass.
• With the motor running, knock the head on the grass
(fig. 13). The string will automatically extend and the
cutting device will reduce it down to the right length.
Note: If the string is shorter than 2.5 cm, it is necessary
to adjust it manually. Press the red push-button on the
coil until it reaches the stop and pull the end of the string.
If you cannot see the end of the string at all, proceed as
described in „Replacing the Mowing String".
Trouble shooting
• Cutting line disappears into spool: Remove spool, pull
end of line through the metal outlet and reinsert spool. In
case nylon line is used up insert a new spool with line.
Do not make any other repairs on your own; have your
trimmer checked and repaired by an authorised dealer.
Maintenance and care
Attention - risk of injury! Always remove the re-
chargeable battery from the device before all work.
Clean your battery-operated mowing machine thoroughly
each time after you use it. Remove the grass and dirt.
Clean the ventilation openings. It is best to clean the
plastic parts with a wet cloth and a soft detergent. Never
use aggressive detergents or solvents. Do not pour water
into the machine and do not sprinkle it with water. Store
the mowing machine in a dry place, never expose it to
frost and keep it out of children's reach.
For more extensive maintenance or repairs, give the
mowing machine to the service center.
Repair service
Repairs to electric power tools should only be carried out
by a specialised electrician.
Waste disposal and environmental protection
If your device should become useless somewhere in
the future or you do not need it any longer, do not dis-
pose of the device together with your domestic refuse,
but dispose of it in an environmentally friendly manner.
Please dispose of the device itself at an according col-
lecting/recycling point. By doing so, plastic and metal
parts can be separated and recycled. Information con-
cerning the disposal of materials and devices are avail-
able from your local administration.
Spare parts
The following information should be provided when or-
GB | Operating Instructions
(fig. 13)
GB-6
dering spare parts:
• Type of machine
• Item number of the machine
Warranty
For this electric tool, the company provides the end
user - independently from the retailer's obligations re-
sulting from the purchasing contract - with the following
warranties:
The warranty period is 24 months beginning from the
hand-over of the device which has to be proved by
the original purchasing document. For commercial use
and use for rent, the warranty period is reduced to 12
months. Wearing parts and defects caused by the use
of non fitting accessories, repair with parts that are not
original parts of the manufacturer, use of force, strokes
and breaking as well as mischievous overloading of
the motor are excluded from this warranty. Warranty
replacement does only include defective parts, not com-
plete devices. Warranty repair shall exclusively be car-
ried out by authorized service partners or by the compa-
ny's customer service. In the case of any intervention of
not authorized personnel, the warranty will be held void.
All postage or delivery costs as well as any other subse-
quent expenses will be borne by the customer.
EC Declaration of Conformity
We, Ikra GmbH, Schlesierstraße 36, D-64839 Münster,
GERMANY, declare under our sole responsibility that the
product Grass trimmer ART 4030 LI, to which this decla-
ration relates correspond to the relevant basic safety and
health requirements of Directives 2006/42/EC (Machinery
Directive), 2004/108/EC (EMC-Guideline), 2011/65/EG
(RoHS-Guideline) and 2000/14/EC, 2005/88/EC (noise
directive) incl. modifications. For the relevant implementa-
tion of the safety and health requirements mentioned in
the Directives, the following standards and/or technical
specification(s) have been respected:
EN 60335-1:2012 +A11:2014; EN 50636-2-91:2014; EK9-
BE-89:2014; EK9-BE-77 (V3):2015; EK9-BE-91:2015
EN 55014-1:2006+A1+A2; EN 55014-2:1997+A1+A2;
EN 50581:2012
measured acoustic capacity level
guaranteed acoustic capacity level
Notified Body Intertek 0905
Conformity assessment method to annexe VI / Directive
2000/14/EC and 2005/88/EC
The year of manufacture is printed on the nameplate and can be
additionally retrieved via the consecutive serial number
Münster, 18.11.2015
Gerhard Knorr, Technical Management Ikra GmbH
Maintenance of technical documentation:
Gerhard Knorr, Kärcherstraße 57, DE-64839 Münster
93,2 dB (A)
96,0 dB (A)