Wolf Garten UV 38 BX Mode D'emploi page 11

Operating HelReg
According to law in some countries lawn mowing not allowed on Saturdays and Sundays and at certain other HelReg (eg. at midday or
after 7 p.m.). Please check noise abatement regulations prevailing in your country.
Assembly
Open the grip rod assembly (Fig. M1)
IMPORTANT: When opening the grip rod assembly, the cable must not get squeezed.
Lift the top part and bottom part of the grip and fold to the rear.
Fasten the bottom part of the grip (Fig. M2)
Lock the bottom part of the grip into place in the recesses and tighten the handwheels by turning them (A).
IMPORTANT: The cable must not get squeezed.
Fasten the height adjustment (Fig. M3)
Move the Work Control Lever (B) forward. Unscrew and remove the winged nut along with bolt and washer. Lift the top part of the grip so that
the lower connecting rod (C) and the upper connecting rod (D) can be brought together in the plastic part (E). Connect the two connecting
rods with the winged nut, bolt and washer.
Fastening the top part of the grip (Fig. M4)
Applying slight pressure, move the top part of the grip to the rear and tighten the handwheels (F).
Anti-kink protection(fig. M4)
IMPORTANT! The cable must always lie in the anti-kink protector M4 (G).
Only move the top part of the grip (Figs. M4/M5)
Only unscrew the handwheels on the top part of the grip M4 (F). Take off the winged nuts on the rod assembly of the height adjustment M5,
or loosen far enough for you to be able to move the top part of the grip and connecting rod forward.
Fold up the complete grip rod assembly (Fig. M1)
IMPORTANT: when folding up the grip rod assembly, the cable must not get squeezed.
Unscrew the handwheels on the bottom part of the grip and on the top part of the grip. Undo the winged nuts along with bolts and washers
from the connecting rods. Press the bottom part of the grip out of the recesses.
Mounting the starter rope (Fig. M6/B5)
Lift Safety Bar B5 (3) and hold it. Slowly draw the starter rope to the grip bar connection, and twist into the guide. Before folding up the grip
rod assembly, twist the starter rope back out.
Attach the catcher sack* (Fig. M7)
Lift the protective shutter. Attach the catcher sack in the recesses in the chassis (see arrow), and put on protective shutter.
(*TK 38, accessory available at an extra charge)
Operation
Filling in the engine oil (Fig. B1)
Before starting up, you have to fill in 0.5 l to 0.6 . of the brand-name oil HD SAE15-"40 up to "Full" marking on the dip stick (not above the
marking). Plug in the dip stick in accordance with (A), and screw in (B); check the oil level.
Before scarifying, always be sure to check the oil level.
Filling in fuel (Fig. B2)
No smoking, and no open flames! Do not tank up with the engine running. Do not squirt fuel while the engine is warm. Use lead-free
regular petrol (not Super Plus). Avoid spilling petrol. Do not inhale the vapours.
Adjust the working depth (Fig. B3)
Only do so with the engine switched off and the scarifying roller having come to a stop. The working depth has to be adjusted to the respective
conditions of the grass and ground.
• Move the Work Control Lever forward (working position).
• Use the twist grip to set the working depth to the desired depth (+)
Scarifi c ation Sampling:
Pull the Work Control Lever back up (transport position).
-
- Start the device.
- Slowly move the Work Control Lever forward.
- Slowly push the device in the working direction.
- If there are any rock impact noises or stalling of the engine, immediately switch off the device.
- Turn the twist grip 1-2 rotations counter-clockwise (-).
- (One rotation is equivalent to 2 mm.)
- Take a new scarification sample.
• After frequent use, the scarification depth can be readjusted according to the wear of the blades (+).
• When the blades have worn to the wear indicator W2 (A), have the complete replaceable roller replaced at a WOLF service shop.
Recommendations on the working depth
Well-kept areas with soft ground free of stones:
• Set the working tool exactly to the level of the ground.
Stony, messy areas:
• Set the working tool to the level of the ground, and lower the working depth if there is any impacting by rocks.
Neglected, very mossy areas:
• Begin with a low working depth, not overloading the device. If the working tool stalls, reduce the working depth (-).
• Scarify several HelReg, doing so crosswise.
11