General Safety Notes; Proper Use; Remaining Hazards - Scheppach dms 900 Traduction Du Manuel D'origine

Controls and features (Fig. 1.1)
1. Headstock
2. Face plate
3. Tool rest with eccentric clamping and release handle
4. Tailstock tip
5. Clamping handle
6. Tailstock
7. Eccentric release handle
tailstock)
8. Drilling bed
9. On/off switch
10. Reversing switch
11. Adjusting lever for engine speed
12. Release handle for headstock
13. Bed extension
14. Frame feet
15. Sole plates
16. Bottom chassis

General Safety Notes

In these operating instructions we have marked the places
that have to do with your safety with this sign.
• Please pass on safety notes and instructions to all those
who work on the machine.
• Comply with all safety instructions and warnings on the
machine.
• Keep all safety instructions and warnings on the ma-
chine fully legible.
• Check all power supply lines. Do not use defective
lines.
• Make sure that the machine stands stable on firm
ground.
• Caution when working: There is a danger to fingers,
hands and eyes.
• Keep children away from the machine when it is con-
nected to the power supply.
• When working on the machine, all safety mechanisms
and covers must be mounted.
• Operating personal must be at least 18 years of age.
Trainees must be at least 16 years of age, but may only
operate the machine under adult supervision.
• Persons working on the machine may not be diverted
from their work.
• The working space on the machine must be free of chips
and wood scrap.
• Wear only close­fitting clothes. Remove rings, bracelets
and other jewelry.
• For the safety of long hair, wear a cap or hair net.
• Do not wear gloves.
• Wear goggles when working.
• Note the motor rotational direction – see electrical con-
nection.
• The safety mechanisms on the machine may not be re-
moved or rendered unusable.
• Cleaning, changing, calibrating, and setting of the ma-
chine may only be carried out when the motor is switched
off. Pull the power supply plug and wait for the rotating
tool to completely stop.
• Switch the machine off and pull power supply plug when
rectifying any malfunctions.
• Connection and repair work on the electrical installation
may be carried out by a qualified electrician only.
• All protection and safety devices must be replaced after
completing repair and maintenance procedures.
• Place the tool support as tightly as possible against the
• The peripheral speed of wooden workpieces must not
• Note the spindle rotation – see reversing switch.
• Provide work pieces with center bores before clamping
• Work large and imbalanced work pieces at a reduced
(on the back of the
• Before switching on the machine, check that the work-
• Remove the chuck key or spring dowel sleeve before
• Always close the belt cover.
• Work with three­ or four­jaw chucks may only be carried
• Never stop work pieces with the hand during run out.
• Work only with well sharpened tools.
• Always use both hands when using turning tool.
• Nicked tools may not be used.
• Note the correct rotational setting on the machine.
• When leaving the work place, switch the motor off. Pull
• Unplug the machine before moving, even if only slightly.
CE tested machines meet all valid EC machine guidelines as
well as all relevent guidelines for each machine.
• The machine must only be used in technically perfect
• The scheppach wood turner has been constructed exclu-
• Any other use exceeds authorization. The manufacturer
• The safety, work and maintenance instructions of the
• Relevant accident prevention regulations and other, gen-
• The scheppach machine may only be used, maintained,
• The scheppach machine may only be used with original
The machine has been built using modern technology in ac­
cordance with recognized safety rules. Some remaining haz­
ards, however, may still exist.
• Only process selected woods without defects such as:
work piece.
exceed 25 m/s. Note spindle speed diagram!
between pivots.
rotational speed; it may be necessary beforehand to cut
accordingly with a band saw.
piece is securely clamped.
turning the machine on.
out with mounted jaw chuck shield.
Never take measurements on a rotating work piece.
the power supply plug.
Correctly connect the machine to the electrical source
before operating again.

Proper use

condition in accordance with its designated use and the
instructions set out in the operating manual, and only
by safety-conscious persons who are fully aware of the
risks involved in oerating the machine. Any functional
disorders, especially those affecting the safety of the
machine, sholud terefore be rectified immediately.
sively for use with wood.
is not responsible for any damages resulting from unau-
thorized use; risk is the sole responsibility of the opera-
tor.
manufacturer as well as the technical data given in the
calibrations and dimensions must be adhered to.
erally recognized safety-technical rules must also be ad-
hered to.
and operated by persons familiar with it and instructed
in its operation and procedures. Arbitrary alterations to
the machine release the manufacturer from all responsi-
bility for any resulting damages.
accessories and tools made by the manufacturer.

Remaining hazards

Branch knots, edge cracks, surface cracks. Wood with
such defects is prone to splintering and hazardous.
english 9