Mains Connection - Güde GDM 450 Traduction Du Mode D'emploi D'origine

Masquer les pouces

Table Des Matières

Table des Matières

Les langues disponibles

Treat electric tools carefully. Check whether the

moving parts work perfectly and do not drag,

whether not broken or damaged to such an extent

that functioning of electric tools could be affected.

Have any damaged parts repaired before using the

machine. Poor maintenance of electric tools is a

cause of many injuries.

Keep the cutting tools sharp and clean. Carefully

treated cutting tools with sharp edges get stuck less

often and are easier to guide.

Follow the instructions for lubricating and chan-

ging tools.

Check the connection cable on the electric tool at

regular intervals and have it replaced by an expert

if it is damaged.

Check the extension cables at regular intervals and

replace them if they are damaged.

Keep the handles dry, clean and free of oil and

grease.

Pull the plug out of the socket and/or remove the

battery when the tool is not in use before you

make machine settings or change accessories,

such as the saw blade, drill bit or cutter. This safety

measure prevents unintentional starting of the

electric tool.

Before starting any electric tool, remove any

adjusting wrenches and screwdrivers. A tool or a

wrench present in the rotating part of the machine

may lead to injuries.

Prevent the machine from unintentional starting.

Before plugging and/or connecting the machine

to battery, handling or carrying, make sure the

electric tools are switched off. Having a finger on

the switch when carrying the electric tool or when the

machine is on when plugging it may lead to injuries.

If you wish to work outdoors with an electric tool,

only use extension cables which are approved for

outdoor use and are marked accordingly. Using an

extension cable suitable for outdoor use reduces the

risk of electric shock.

Be careful, pay attention to what you are doing

and use common sense when working with

electric tools. Do not use electric tools when you

are tired or under the influence of drugs, alcohol

or pharmaceuticals. A moment if inattention when

using electric tools may lead to serious injuries.

Check the machine for any damage. Before using

the equipment again, the protective equipment

must carefully be checked if safe and working as

designated.

Check the moving parts for perfect functioning, if

working smoothly and if no parts are damaged. To

provide safe operation of the equipment, all parts

must be installed properly and meet all conditions.

Damaged protective equipment and parts must be

professionally repaired or replaced by a recognised

professional workshop, unless otherwise specified

in the Operating Instructions.

Do not use electric tools with a defective switch.

An electric tool that cannot be switched on or off is

dangerous and must be repaired.

Have your electric tool repaired by an electrician.

This electric tools complies with the relevant safety

regulations. Repairs may only be carried out by an

electrician using genuine spare parts; otherwise the

user may suffer accidents.

Inspect before each use.

• Proper function of the on and off button, incl. the

emergency switch.

• Carry out a visual inspection before switching the

appliance on.

• Check especially the safety equipment, electrical

control elements, power lines and screw couplings

for any damage and if they are tightened approp-

riately. If necessary, replace damaged parts before

operation.

• REMOVE ADJUSTING KEYS AND WRENCHES. From

habit of checking to see that keys and adjusting

wrenches are removed from tool before turning

it "ON".

Risk of injury!

Keep body parts and clothes away from rotating

parts of the device.

Use protective equipment which fit you.

<<Tragen Sie geeignete Kleidung. Tragen Sie keine

weite Kleidung oder Schmuck. Halten Sie Haare,

Kleidung und Handschuhe fern von sich bewegenden

Teilen. >>

Wear a hairnet if you have long hair.

Make sure that the machine is always securely positi-

oned (e.g. mounted to the workbench)

Set the woodturning machine to the spindle speed

that is appropriate for the current job.

Do not use wooden discs that have shrinkage cracks

as there is a high risk of breakage due to centrifugal

force.

In the event of a blockage, switch off the machine

immediately.

Pull out the mains plug and remove the jammed

workpiece.

Chips and splinters must not be removed while the

machine is running.