Publicité
Les langues disponibles
Les langues disponibles
LED: total: 256, Red: 96pcs, Green: 96pcs, Blue: 64pcs
Dimension: 965 x 190 x 185mm
Weight: 6.3kgs
3. Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit
is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of 10
times of the unit's weight. Also always use a safety cable that can hold 12 times of the
weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out
of the touch of people and has no one pass by or under it.
4. How To Control The Unit
4.1 Master/Slave Operation
The unit can be linked together in daisy chain as many as you need in master/slave mode
to perform the great built-in pre-programmed lighting shows triggered by music.
In Master/Slave mode refer to the DMX settings below:
Master unit: Set all DIP switchs to OFF
Slave 1: Set DIP switch 1 to ON
2-light show: Set DIP switch 1 and 10 to ON
In order to create a great light show, you can set dip switch 10 "on" on any unit that is
linking to the master unit to get contrast movement to the master unit, even if you have two
units only. Dipswitch 10 on the first (Master) unit is no use for the 2-light show as it is the
master unit that operates the light show.
4.2 Easy Controller (by CA-8)
The easy remote control is used only in master/slave mode. There is a
terminator for connect the easy controller inside the fixture. By connecting
the cable into DMX IN waterproof cable entry gland to the CA-8 terminator of
the first fixture, you will find that the remote control on the first fixture will
control all the other fixtures for Stand by, Function and Mode functions.
12
Stand by
Blackout the unit
1. Synchronous Strobe
Function
2. Sound Strobe
3. Two light Strobe
Mode
Strobe (LED OFF)
4.3 DMX Controller
When using a universal DMX controller to control the chain of units, you have to set DMX
address by Dip switches from 1 to 9 to make sure all the units will receive its DMX signal.
The dip switch 10 is used to choose channel mode. Please refer to the following diagram to
know how to address your DMX 512 system in the binary code.
DMX 512 Address Chart:
Dip-switches
# 1
# 2
# 3
# 4
Value
1
2
4
• Examples:
Set dip switch 10 to ON, the unit is in 1 channel mode
Unit 1
Unit 2
Unit 3
Unit 4
Set dip switch 10 to OFF, the unit is in 6 channels mode
Unit 1
Unit 2
Unit 3
Unit 4
5. DMX 512 Configuration
1 & 6-CH modes:
Select show
1-12
Show (LED ON)
# 5
# 6
# 7
# 8
# 9
8
16
32
64
128
256
：
d ip / on: #1 (=1)
d ip / on: #2 (=2)
：
：
d ip / on: #1, #2, (1+2=3)
d ip / on: #3 (=4)
：
d ip / on: #1 (=1)
：
：
d ip / on: #1, # 2, #3 (1+2+4=7)
d ip / on: #1, #3, #4 (1+4+8=13)
：
：
d ip / on: #1, #2, #5 (1+2+16=19)
13
#10
CH mode
Publicité
