How To Control The Unit; Dmx Controller - Nicols SPARK LED Manuel D'utilisation

Pressing ENTER button. Use DOWN and UP button to select the Yes or No
Blackout, Back to the main functions, press the MENU button twice.
Slave Mode
Press the MENU button up to when the
button, Use DOWN and UP button to select the
Back to the previous functions without any change press MENU button.
LED
Press the MENU button up to when the
button and the display will blink. Use DOWN and UP button to select the (ON) or (OFF)
mode. Once the mode has been selected, press ENTER button to setup or automatically
return to the main functions without any change after 10 seconds. Back to the functions
without any change press MENU button again.
Display Inverse
Press MENU button until is blinking on the display. Pressing ENTER button. Once
the mode has been selected, press ENTER button to setup or automatically return to the
main functions without any change after 10 seconds. Back to the functions without any
change press MENU button again.
Fixture Hours
Press the MENU button up to when the
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button again.
Software version
Press the MENU button up to when the
button and the display will show the version of software of the unit. To go back to the
functions press the MENU button again.

4. How To Control The Unit

You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. By easy controller
3. By iLead controller (Please refer to the user guide of iLead) or universal DMX controller
No need to turn the unit off when you change the DMX address, as new DMX address
setting will be effected at once. Every time you turn the unit on, it will show 200S on the
display and move all the motors to their 'home' position and you may hear some noises for
about 20 seconds. After that the unit will be ready to receive DMX signal or run the built in
programs.
4.1 Master/Slave Built In Preprogrammed Function
is shown on the display. Pressing ENTER
or (Slave Mode 1and 2).
is shown on the display. Pressing ENTER
is blinking on the display. Pressing ENTER
is blinking on the display. Pressing ENTER
12-
By linking the units in master/slave connection, the first unit will control the other units to
give an automatic, sound activated, synchronized light show. This function is good when
you want an instant show. You have to set the first unit in master mode
(show 1) or (show 2) or
input jack will have nothing plugged into it, and Its master LED will be constantly on and
sound LED will flash to the music. The other units will have to set in slave mode
and select (normal) or (2 light show) mode, Their DMX cables plugged into
the DMX input jacks (daisy chain) and the slave led lights will constantly on.
2-light show
In (slave mode), means the unit works normally and
show. In order to create a great light show, you can set
contrast movement to each other, even if you have two units only.
4.2. Easy Controller (by CA-8)
The easy remote control is used only in master/slave mode. There is a
terminator for connect the easy controller inside the fixture. By connecting the
cable into DMX IN waterproof cable entry gland to the CA-8 terminator of the
first fixture, you will find that the remote control on the first fixture will control all
the other fixtures for Stand by, Function and Mode functions.
Blackout Blackout the unit
1. Synchronous Strobe
Function 2. Sound Strobe
3. Two light Strobe
Sound/Strobe
Mode
(LED OFF)
4.3 iSolution Operation
Consistent DMX configuration enable iMove to be linked together with iRock and
♦
iShow and controlled at the same time.
DMX address can be set remotely by iLead controller (Please refer to the user manual
♦
of iLead controller). No need to calculate the DMX channels of each fixture in the chain.
Automatic switching between DMX function and built-in stand alone programs.
♦

4.4 DMX Controller

and select
(show 3) or (show 4) mode. Its DMX
means 2-light
on the second unit to get
Chase Select
(Chase 1-10)
Chase
(LED ON)
13-