Variable Speed Switch; To Use The Car Polisher; Finishing; Working Hints For Your Polisher - Batavia MAXX Série Mode D'emploi

English

12. Variable speed switch

(See Fig. E).
The speed increases as you turn the Varia-
ble Speed Switch(7) towards the higher
number and decreases on the lower
number.
Thumbwheel position 1 provides the slow-
est operating speed and position 6 the fast-
est. Speed may be changed while motor is
running or while it is stopped.

13. To use the car polisher

(See Fig. F).
Hold extension cord over the shoulder and
do flat surfaces first, i.e.: bonnet boot and
roof. Cover areas quickly with broad sweep-
ing strokes in a crisscross pattern. Do not
press down on polisher. The machine with-
out any pressure will automatically do the
best job.

14. Finishing

(See Fig. G).
Use long, sweeping strokes in a criss-cross
pattern to bring out the shine. Do not over-
press the polisher.

15. Working hints for your polisher

At all times, let the polisher do the work
15.1
– do not force it or apply excessive
pressure to the polisher. Preferably, use
a light circular motion. Pressing too
hard will slow down the machine's
movement and affect the quality of the
work.
The most common error, however, is
15.2
applying too much wax. If pad absorbs
too much wax, it will not last as long,
and polishing is more difficult and takes
longer.
If bonnet continually comes off pad,
15.3
please try with a new bonnet.
If wax seems difficult to buff, you may
15.4
have used too much wax.

16. Accessories

Use only accessories with an allowable
speed matching at least the highest no-load
speed of the tool.
8
7062891-Eccentric_Polisher-600W-Ma-1803-13.indb 8

17. Maintenance and Cleaning

WARNING: Always disconnect from the
mains power supply, before carrying out any
maintenance/ cleaning of the charger.
Remove the battery before carrying out any
maintenance/cleaning of the tool.
Maintenance
17.1
There are no inner parts of the tool which
need maintenance.
Cleaning
17.2
• Keep safety devices, ventilation open-
ings and the motor housing as free as
possible from dirt and dust. Rub the
electric power tool with a clean cloth or
blow over it with low pressure com-
pressed air.
• We recommend that you clean your
electric power tool immediately after
each use.
• Clean the electric power tool regularly
with a damp cloth and somewhat soft
soap.
Do not use any cleaning or solvent materi-
als; these can attack the device's plastic
components. Make sure that no water can
get inside the electric power tool.

18. Technical data

Nominal voltage:. . . 230 – 240 V / ~50 Hz
Rated power: . . . . . . . . . . . . . . . 600 W
No-load speed:. . . . . . 1500 – 6800 min
Diameter base plate: . . . . . . . . .150 mm
Spindle thread size: . . . . . . . . . . . . .M8
Weight: . . . . . . . . . . . . . . . . . 2.22 kg
Protection Class:. . . . . . . . . . . . . . . . II
Sound Pressure Level L
Uncertainty K : . . . . . . . . . . . . . . 3 dB
pA
Sound Power Level L : . . . . . . . 91 dB(A)
WA
Uncertainty K : . . . . . . . . . . . . . . 3 dB
WA
Hand Arm Vibration:. . . . . . . . .< 2.5 m/s
Uncertainty K: . . . . . . . . . . . . .1.5 m/s
-1
: . . . . . 80 dB(A)
pA
2
2
22-03-18 11:13