Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
General Safety Instructions
Read the operating instructions carefully before putting the
appliance into operation and keep the instructions including the
warranty, the receipt and, if possible, the box with the internal
packing.
•
The appliance is designed exclusively for private use
and for the envisaged purpose. This appliance is not fi t
for commercial use. Do not use it outdoors (except if it is
designed to be used outdoors). Keep it away from sources
of heat, direct sunlight, humidity (never dip it into any liquid)
and sharp edges. Do not use the appliance with wet hands.
If the appliance is humid or wet, unplug it immediately. Do
not put it in water.
•
When cleaning or putting it away, switch off the appliance
and always pull out the plug from the socket (pull on the
plug, not the cable) if the appliance is not being used and
remove the attached accessories.
•
Do not operate the machine without supervision. If you
should leave the workplace, always switch the machine off
or remove the plug from the socket (pull the plug itself, not
the lead).
•
Check the appliance and the cable for damage on a regular
basis. Do not use the appliance if it is damaged.
•
Do not try to repair the appliance on your own. Always
contact an authorized technician. To avoid the exposure
to danger, always have a faulty cable be replaced only by
the manufacturer, by our customer service or by a qualifi ed
person and with a cable of the same type.
•
Use only original spare parts.
•
Pay careful attention to the following "Special Safety Instruc-
tions".
Children
•
In order to ensure your children's safety, please keep all
packaging (plastic bags, boxes, polystyrene etc.) out of their
reach.
Caution! Do not allow small children to play with the foil as
there is a danger of suffocation!
•
To protect children from the dangers posed by electrical
appliances, make sure that the cable is hanging low and that
children do not have access to the appliance.
Special safety notes for this unit
•
Place the unit on a fl at and heat-resistant surface. In the
case of sensitive surfaces please place a heat-resistant
board under the pan.
•
Only the supplied thermostat (7) may be used.
No other regulator should be used under any circum-
stances!
•
Before inserting or removing the thermostat (7) please
ensure that the scale of the temperature regulator (11) is
turned to 0 (off). Otherwise the device may fail to operate or
overheat.
05-TYG 3027 31
•
When inserting the thermostat (7) please ensure that it is
inserted correctly. The regulator (11) should be facing up-
wards. When removing the thermostat, do not pull the cable,
but pull on the plug of the thermostat. Do not use excessive
force or bend the thermostat when inserting or removing it.
•
Please keep the temperature sensor (8) and the pins of the
holder clean.
•
Warning: Danger of fi re!
Keep the unit at a safe distance from easily infl ammable
objects such as furniture, curtains, etc. (30 cm).
Oil and fat preparations may burn if overheated.
•
Please ensure that the mains lead does not come into con-
tact with the hot sections of the device. Do not touch the hot
sections of the device; please use the buttons and handles
provided.
•
Never pour water into hot fat.
•
Allow the unit to cool down before you put it away.
Overview of the Components
1 Foot
2 Grease trough
3 Socket for the thermostat
4 Fat collecting pan
5 Handle
6 Hot plate
7 Thermostat
8 Temperature sensor –
measures the temperature of the plate
9 Mains lead
10 Mains plug
11 Thermostat control
Before Initial Use
•
Remove the packaging.
•
We recommend that you clean the device as described
under „Cleaning".
Initial Operation
•
Place the device on a heat-resistant surface.
•
Please ensure that the temperature regulator (11) is turned
to 0 (off) and insert it into the socket (3) of the thermostat.
If the thermostat (7) is not inserted correctly, this may lead
to abnormal heating, of which the consequence may be
damage or accidents. You should therefore ensure that the
thermostat is inserted correctly.
•
Connect the device to a properly installed 230 V, 50 Hz
power socket.
•
Set the temperature control (11) according to what you
intend to do:
31
22.03.2006, 9:53:53 Uhr
Publicité
Table des Matières
