Important Safety Instructions - Simer 2943 Notice D'utilisation

Specifications and Safety
Im portant Safety
Instructions
SAVE THESE INSTRUCTIONS - This manual
contains important instructions that should be
followed during installation, operation, and
maintenance of the product.
This is the safety alert symbol. When you
see this symbol on your pump or in this manual,
look for one of the following signal words and
be alert to the potential for personal injury!
indicates a hazard which, if not
avoided, will result in death or serious injury.
indicates a hazard which, if not
avoided, could result in death or serious injury.
indicates a hazard which, if not
avoided, could result in minor or moderate injury.
NOTICE addresses practices not related to
personal injury.
Carefully read and follow all safety instructions
in this manual and on pump.
Keep safety labels in good condition. Replace
missing or damaged safety labels.
California Proposition 65 Warning
This product contains chemicals
known to the State of California to cause cancer
or birth defects or other reproductive harm
Specifications
Power supply required ................. 115V, 60 HZ.
Liquid Temp. Range ......... 32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.) ...... 15
Amps
Discharge:
Plastic Models ....1-1/4" FNPT / 1-1/2" MNPT
Cast Iron Models ........................1-1/2" FNPT
NOTICE Do not reduce size of discharge pipe or
hose below 1-1/4" diameter. If discharge is too
small, pump will overheat and fail prematurely.
NOTICE This unit is not designed for
applications involving salt water or brine! Use
with salt water or brine will void warranty.
Pump water only with this pump.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
Performance
GPH (LPH) At Total Feet (m) of Lift
Model HP 5 (1.5m)
Capacity Gallons (L)/Hour
2760
2943 1/3
(10 448)
2800
2956 1/3
(10 599)
2945
3200
1/2
(12 113)
2958
For parts or assistance, call Simer Customer Service at
15 No
10(3m)
(4.6m) flow at
height
shown
below
2160 1410 20 Ft.
(8 176) (5 337) (6.1M)
2200 1400 20 Ft.
(8 328) (5 299) (6.1M)
2700 2000 24 Ft.
(10 200) (7 571) (7.3M)
Electrical and Switch Specifications
Motor
Full
Model HP
Load
Amps
2943 1/3 9.0
2945 1/2 5.5
2956 1/3 9.0
2958 1/2 6.0
1. Know the pump application, limitations, and
potential hazards.
2. Do not use in water with fish present.
3. Disconnect power before servicing.
4. Release all pressure within system before
servicing any component.
5. Drain all water from system before servicing.
6. Secure discharge line before starting pump.
An unsecured discharge line will whip,
possibly causing personal injury and/or
property damage.
7. Check hoses for weak or worn condition
before each use, making certain that all
connections are secure.
8. Periodically inspect sump, pump and system
components. Keep free of debris and foreign
objects. Perform routine maintenance as required.
9. Provide means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
10. Personal Safety:
a. Wear safety glasses at all times when
working with pumps.
b. Keep work area clean, uncluttered and
properly lighted – replace all unused
tools and equipment.
c. Keep visitors at a safe distance from
work area.
d. Make workshop child-proof – with
padlocks, master switches, and by
removing starter keys.
11. When wiring an electrically driven pump,
follow all electrical and safety codes that apply.
12. This equipment is only for use on 115 volt
(single phase) and is equipped with an approved
3-conductor cord and 3-prong, grounding-type plug.
Risk of electric shock. Can shock,
burn or kill. Pull plug before servicing. This
pump has not been investigated for use in
swimming pool areas. Pump is supplied with
a grounding conductor and grounding-type
attachment plug. Be sure it is connected
only to a properly grounded grounding-
type receptacle.
800-468-7867
Individual *Switch Setting in
Branch inches (mm)
Circuit
Req.
On
(Amps)
15 13"(330) 6"(152)
15 13"(330) 6"(152)
15 8"(203) 3"(102)
15 8"(203) 3"(102)
2
Off