stayer SC241W Instructions D'emploi page 44

5.Exert pressure in the blade's direction of advance
with an intensity being suitable for the material to
be cut.
6. Once the cutting operation has been completed,
raise operating head again. Stop the machine by
pushing switch 2.
Use as circular saw by means of the upper
cutting table
Information:
This chapter is not applicable for models lacking an
upper cutting table: SC264W.
This chapter is applicable to models provided with
an upper table: SC241W, SC 250W PRO, SC261W,
SC265W, SC291W, SCE1650W and SLL265W.
Warning!
Before carrying out any operation on the upper
cutting table it is mandatory to prepare the machine
suitably. For this purpose, the stationary safety
guard is to be installed on the lower table.
Installing the stationary safety guard on the
lower cutting table
IMAGES
A B V
1.Begin with the head raised and the cable
unplugged.
2.Loosen frontal wing nut 24.
3.Insert the guide of safety guard 34 onto the screw
of wing nut 24.
4.Apply guard 34 at its location according to the
figure.
5.Smoothly lower the head and block it by means of
button 31.
6.Push guard 34 downwards ensuring that the
guard abuts against the lower cutting table.
7.Firmly tighten wing nut 24.
8.Check that the blade rotates freely.
9.Finally, briefly start the machine without load and
ensure that the disk does not friction.
10.Disconnect the electrical power jack again.
Setting the upper table
Setting the height of the upper cutting table
IMAGES
A B O
Information:
The height of the upper cutting table can be
adjusted from 0 to 42mm.
Warning!
The height of the upper cutting table in respect of
ENGLISH
34
W
34
the cutting disk must be such that the disk protrudes
from the workpiece only by a height equal to that of
the saw tooth. See image W.
1.If tightened, slightly loosen the screw of the shaft
of the guard of table 25 such that the guard
ascends freely.
2.If tightened, loosen lock 38 of the guard of table 25
such that the guard ascends freely.
3.Loosen the wing nuts 24 that regulate the height
of the upper table.
4.Adjust the height of the table by smoothly pulling it
upwards.
5.Firmly tighten the wing nuts 24.
Setting the cutting width on the upper table
by means of the guide
IMAGES
B P
1.Release movement of the parallel guide 27 by
loosening wing nut 28.
2.Adjust the cutting width by moving the guide 27 on
the graduated scale 45.
3.Fasten guide 27 by firmly tightening the wing nut
28.
Using the goniometer
Information!
IMAGES
P Q
The upper working table is set for the optional use of
a goniometer that is adjustable between 0º and 45º.
The regular use of the goniometer is for cutting
slanted cuts, but there is the possibility to use the
goniometer as a depth control stop for adjustable
cutting. Mount the goniometer at the right side of the
upper cutting table for this purpose.
There is a model-specific goniometer for upper
aluminum tables (SC250W, SC261W, SC265W,
SC291W, SC2500W, SCE1650W, and SLL265W)
and another for upper steel-plate tables (SC241W
und SC 250W PRO).
1.Loosen the lower wing nut for coupling to the
upper cutting table.
2.Insert the goniometer into the front slot of the
upper cutting table.
3.Adjust the position of the goniometer in
accordance with the work to be carried out.
4.Tighten the wing nut for coupling the goniometer
to the upper cutting table.
5.Loosen the upper wing nut for adjusting the angle
of the goniometer.
6.Adjust the angle of the goniometer in accordance
with the work to be carried out.
7.Tighten the upper wing nut for adjusting the angle
of the goniometer.
8.Loosen the upper stop-extension wing nuts of the
goniometer.