Peg-Perego PRIMO VIAGGIO Lounge Mode D'emploi page 16

in all parts. An obsolete product may not conform to
safety standards, due to natural ageing of materials and
updating of regulations. If you have any doubts, contact the
manufacturer's customer service centre.
• Make sure there are no items of luggage or other unsecured
items in the vehicle interior. They could injure the vehicle's
occupants in the event of an accident.
• This product requires only minimal cleaning and
maintenance. These operations must be performed by
adults.
• It is advisable to keep all the moving parts clean.
• Clean plastic parts periodically with a damp cloth. Do not
use solvents or similar substances.
• Do not clean the polystyrene shock absorbing device with
solvents or other similar products.
• Brush fabric parts to remove dust. If you wash fabric parts,
follow the washing instructions on the laundry label.
• Protect the product from atmospheric agents: humidity, rain
or snow. Extended exposure to sunshine can cause colour
changes in many materials.
• Store the product in a dry environment.
WARNING: FOR USE AS A RECLINED
CRADLE.
• Do not use the reclined cradle once your child can sit
unaided.
• This reclined cradle is not intended for prolonged
periods of sleeping.
• It is dangerous to use this reclined cradle on an elevated
surface, e.g. a table.
Components of the Product
Inspect the content of the package and contact Customer
Care if any items are missing.
The child car seat includes:
a) Hood
b) Handlebar
c) Dual Stage Cushion
d) Headrest
e) Harness tension release button
f ) Harness tension adjustment strap
g) 3-point safety harness with shoulder straps
h) Reclining lever
i) Headrest height adjustment button
l) Instruction manual compartment
m) Headrest lined with shock-absorbing expanded polystyrene
(EPS)
n) Shock-absorbing expanded polystyrene (EPS) inserts
o) Kinetic Pods: side protections.
p) Lever for release from base
q) Chest Clip
The car seat is ready for use: no assembly required.
How to install the car seat with the base
Primo Viaggio Lounge features the Ganciomatic System
for connection and release in the car with the Base
i-Size.
When used with Base i-Size, you can use Primo Viaggio
Lounge with a reclined backrest.
1 To recline the backrest in the 3 positions available, use the
handlebar on the upper end of the backrest.
2 Attach the car seat to Base I-Size. Release the car seat by
pulling the lever on the lower end of the backrest while
lifting the car seat.
3 Adjust the base so that the car seat is neither distant from
the vehicle seat's backrest nor against it preventing its
correct attachment (as shown in the figure).
4 Pull the handlebar on the base and push it or move it away
from the vehicle seat's backrest.
You can check whether the car seat is attached correctly to
the base through the red and green indicators at the back of
the base.
5 Press the two buttons on the handlebar, rotate it and
position it in the direction of the vehicle seat. Installation is
now complete.
6 The car seat handlebar has four fixed positions. To rotate it,
press the two buttons on the handlebar and move this to
the required angle. Ensure it clicks into position.
• Position A: the in-vehicle position;
• Position B: the position for transport by hand and for
installation on a base, stroller or chassis;
• Position C: this is the resting position;
• Position D: stops the car seat from rocking.
How to install the car seat without the
base
When used without Base i-Size, you can install Primo
Viaggio Lounge with the BACKREST IN THE UPRIGHT
POSITION, ONLY.
7 If the backrest is reclined, use the handlebar on the upper
end of the backrest to bring it to the upright position.
IMPORTANT! The car seat must be parallel to the
ground. If necessary, you can place rolled-up towels or
swimming pool float tubes in the folds of the vehicle's seats,
as shown in the figure.
Fit the car seat with the child seated inside, remembering to
secure the child with the harness.
8 Slide the lower part of the vehicle seatbelt into the two
guides on the car seat (fig_a) and buckle it (fig_b), ensuring
the seatbelt is taut, as shown in the figure.
Grasp the upper part of the vehicle seatbelt and pass it
behind the car seat backrest (fig_c).
16