Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
5.1 Setting the transmitter
When the transmitter is not locked, press the but-
ton SET (4) to activate the setting modes one after
another:
group (keep button pressed for a while) channel
sensitivity automatic frequency matching
identification number lock function
To make settings in a setting mode, see the corre-
sponding chapter (5 1 1 to 5 1 5)
To exit a setting mode without changing a setting,
press the button SET repeatedly until the display
briefly shows
the normal mode
5.1.1 Transmission frequency (group / channel)
To set the transmitter quickly and easily to the
transmission frequency of the receiver unit, use the
REMOSET function (
it is also possible to set the transmission frequency
of the transmitter manually by selecting the chan-
nel group and the channel The table on page 20
gives an overview of the groups and channels
1) Keep the button SET (4) pressed until the display
briefly shows
(
...
) starts flashing; the group setting mode
is activated
2) Select the group with the button − (5) or the
button + (6)
3) Press the button SET to confirm The channel
indication starts flashing on the display; the
channel setting mode is activated
4) Select the channel with the button − or the
button +
5) Press the button SET to confirm The display
briefly shows
the normal mode
5.1.2 Sensitivity
For the sensitivity, several levels are available: from
12 dB (maximum sensitivity) to −18 dB (minimum
sensitivity)
1) Keep the button SET (4) pressed until the display
briefly shows
mode (group indication starts flashing)
2) Press the button SET repeatedly until the dis-
play briefly shows
sensitivity
3) Press the buttons − (5) and + (6) to set the sen-
sitivity in such a way that you obtain an opti-
mum volume level of the microphone If the
10
The unit will then return to
☞
chapter 5, step 4) However,
Then the group indication
The unit will then return to
and then the group setting
and then the current
volume is too high, the microphone will distort;
in this case, set a lower value with the button −
If the volume is too low, there will be a poor
signal-to-noise ratio; in this case, set a higher
value with the button +
4) Press the button SET to confirm The display
briefly shows
the normal mode
5.1.3 Automatic frequency matching
(REMOSET function)
To enable /disable the automatic frequency match-
ing (REMOSET function = frequency setting of the
transmitter via a radio signal of the receiver unit)
for the transmitter:
1) Keep the button SET (4) pressed until the display
briefly shows
mode (group indication starts flashing)
2) Press the button SET repeatedly until the display
shows the current setting for the automatic fre-
quency matching:
automatic frequency matching enabled
(i e frequency setting of the transmitter
via the REMOSET function is possible)
automatic frequency matching disabled
(i e no REMOSET transmission)
3) Press the button − (5) to select the setting
or press the button + (6) to select the setting
4) Press the button SET to confirm The display
briefly shows
the normal mode
5.1.4 Identification number
To enable the REMOSET transmission between the
transmitter and the receiver unit, match their iden-
tification numbers
1) Keep the button SET (4) pressed until the display
briefly shows
mode (group indication starts flashing)
2) Press the button SET repeatedly until the display
shows
and the current identification number
( ...
or
)
3) In the setting range
the button − (5) to search in descending order
or press the button + (6) to search in ascending
order Use the corresponding button to set the
transmitter to the identification number of the
receiver unit (the transmitter will only respond
to the REMOSET signal of this receiver unit) or
The unit will then return to
and then the group setting
The unit will then return to
and then the group setting
,
...
press
Publicité
Table des Matières
