General Information - Flotec FPSS5700A Notice D'utilisation

General Information

DESCRIPTION
This Stainless Steel Submersible Sump Pump is designed for
drainage of sump pits and flooded basements, dewatering
flooded areas, and to provide laundry drainage. Operates
automatically. Has a 115V, 60 Hz., single phase, permanent split
capacitor motor. Pump casing, suction strainer, impeller and shaft
are all stainless steel. Permanently lubricated ball bearings.
Automatic thermal overload protection. Equipped with a 15' 16/3
grounding-type power cord and tethered float switch.
Non-clog cast stainless steel impeller, ceramic shaft facings, and
stainless steel oil chamber for seal lubrication.
SPECIFICATIONS
Power supply required...................................115V, 60 HZ.
Liquid Temp. Range.......................................32° F to 130° F
Dedicated Circuit Requirement (minimum)...15 Amps
Pump Discharge............................................1-1/4" MNPT
Discharge Adapter:........................................1-1/4"FNPT Elbow
UNPACKING AND INSPECTION
Handle with care. Check item received against packing list to be
sure that equipment is correct. Inspect for shipping damage. If
found, file claim with carrier immediately.
GENERAL SAFETY INFORMATION
READ AND FOLLOW SAFETY INSTRUCTIONS!
Electrically powered sump pumps normally give many years of
trouble-free service when correctly installed, maintained, and
used. However, unusual circumstances (interruption of power to
the pump, dirt/debris in the sump, flooding that exceeds the
pump's capacity, electrical or mechanical failure in the pump,
etc.) may prevent your pump from functioning normally. To
prevent possible water damage due to flooding, consult your
retailer about a secondary AC sump pump, a DC backup sump
pump, and/or a high water alarm. See the "Troubleshooting
Chart" in this manual for information about common sump
pump problems and remedies.
Know the pump application, limitations, and potential hazards.
Disconnect power before servicing.
Release all pressure within system before servicing any
component.
Drain all water from system before servicing.
Secure discharge line before starting pump. An unsecured
discharge line will whip, possibly causing personal injury and/or
property damage.
Check hoses for weak or worn condition before each use,
making certain that all connections are secure.
Periodically inspect sump, pump, and system components. Keep
free of debris and foreign objects. Perform routine maintenance
as required.
For parts or assistance, call Flotec Customer Service at
Personal Safety:
1. Wear safety glasses at all times when working with pumps.
2. Keep work area clean, uncluttered, and properly lighted –
replace all unused tools and equipment.
3. Keep visitors at a safe distance from work area.
4. Make workshop child-proof – with padlocks, master switches,
and by removing starter keys.
When wiring an electrically driven pump, follow all electrical
and safety codes that apply.
This equipment is only for use on 115 volt (single phase) and is
equipped with an approved 3-conductor cord and 3-prong,
grounding-type plug.
servicing. This pump has not been investigated for use in
swimming pool areas. Pump is supplied with a grounding
(0° C to 54° C)
conductor and grounding-type attachment plug. Be sure it is
connected only to a properly grounded grounding-type
receptacle. Where a 2-prong wall receptacle is encountered, it
must be replaced with 2 properly grounded 3-prong receptacle
installed in accordance with codes and ordinances that apply.
All wiring should be performed by a qualified electrician.
Make certain power source conforms to requirements of your
equipment.
Protect electrical cord from sharp objects, hot surfaces, oil, and
chemicals. Avoid kinking cord. Replace or repair damaged or
worn cords immediately.
Do not handle pump or pump motor with wet hands or when
standing on wet or damp surface, or in water.
Do not use this pump where fish are present.
basement has water or moisture on floor, do not walk on wet
area until all power has been turned OFF. If shut-off box is in
basement, call electric company or hydro authority to shut-off
service to house, or call your local fire department for
instructions. Remove pump and repair or replace. Failure to
follow this warning can result in fatal electrical shock. Oil on
the pump or in the sump may indicate motor leakage and
electrical shock hazard. Turn OFF power and check pump for
oil leakage from impeller area. Replace pump if it leaks.
NOTE: This unit is not designed for applications involving salt
water or brine! Use with salt water or brine will void warranty.
Pump water only with this pump.
To reduce risk of electric shock, pull plug before
Risk of electrical shock. Can burn or kill. If your
1-800-365-6832
2