Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Try to anticipate what may happen, observe what is
going on and use common sense when working with
the device.
b)
Do not use the device in an explosion hazard zone,
for example in the presence of flammable liquids,
gasses or dust. The device generates sparks which
may ignite dust or fumes.
c)
Upon discovering damage or irregular operation,
immediately switch the device off and report it to
a supervisor without delay.
d)
If there are any doubts as to the correct operation
of the device, contact the manufacturer's support
service.
e)
Only the manufacturer's service point may repair the
device. Do not attempt any repairs independently!
f)
If a fire starts, use solely powder or carbon dioxide
(CO
) fire extinguishers suitable for use on live
2
devices to put it out.
g)
Children or unauthorised persons are forbidden
from entering a work station. (A distraction may
result in a loss of control over the device).
h)
Use the device in a well-ventilated space.
i)
During operation, dust and debris are produced,
making it is necessary to protect unauthorized
persons against their harmful effects.
REMEMBER! When using the device, protect children
and other bystanders.
3.3. Personal safety
a)
Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
b)
The machine may be operated by physically fit
persons who are able to handle the machine and
properly trained and who reviewed this operating
manual and received training in occupational health
and safety.
c)
The machine is not designed to be handled by
persons (including children) with limited mental
and sensory functions or persons lacking relevant
experience and/or knowledge unless they are
supervised by a person responsible for their safety
or they have received instructions on how to operate
the machine.
d)
When working with the device, use common sense
and stay alert. Temporary loss of concentration
whilst using the device may lead to serious injuries.
e)
Use personal protection equipment as required
for working with the device, specified in section 1
(Legend).
The use of correct, approved personal protection
equipment reduces the risk of suffering an injury.
f)
To prevent the device from accidentally switching on,
make sure the switch is on the OFF position before
connecting to a power source.
g)
Do not wear loose clothing or jewellery. Keep your
hair, clothes and gloves away from any moving parts.
Loose clothing, jewellery or long hair may get caught
in the moving parts.
h)
Remove all adjusting tools or spanners before
turning the device on. A tool or spanner left in the
revolving part of the device may cause injury.
10
3.4 Safe device use
a)
Do not overload the device. Use appropriate tools
for the given task. A correctly selected device will
perform the task for which it was designed better
and in a safer manner.
b)
Do not use the device if the ON/OFF switch does not
function properly (does not switch the device on and
off). Devices which cannot be switched on and off
using the ON/OFF switch are hazardous, should not
be operated and have to be repaired.
c)
Make sure the plug is disconnected from the
socket before attempting any adjustments, tool
replacements or before putting the device aside.
Such precautions will reduce the risk of accidentally
activating the device.
d)
When not in use, store in a safe place, away from
children and people not familiar with the device, who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
e)
Maintain the device in a good technical state. Before
each use check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of
the device. If damage is discovered, hand over the
device for repair before use.
f)
Keep the device out of the reach of children.
g)
Device repair or maintenance should be carried out
by qualified persons, only using original spare parts.
This will ensure safe use.
h)
To ensure the operational integrity of the device, do
not remove factory fitted guards and do not loosen
any screws.
i)
When transporting and handling the device between
the warehouse and the destination, take into account
the occupational health and safety principles for
manual transport operations which apply in the
country where the device will be used.
j)
Avoid situations where the device halts during
use due to excessive loading. This may result in
overheating of the drive elements and device
damage.
k)
Do not touch any articulated parts or accessories,
unless the device has been disconnected from
a power source.
l)
When working with the machine, it is necessary to
pay special attention to the recoil phenomenon,
which is a sudden reaction of the machine to
blockade of the rotating working tip. The rotating
tool blockade sequence is a swing of the machine
in the opposite direction to the rotation direction of
the working tip. Recoiling is the result of incorrect
machine use.
m)
Regularly clean the ventilation slots of the machine
n)
Do not move or transport the device while it is in
operation.
o)
It is not allowed to leave the tool started without
supervision.
p)
It is not allowed to machine two items at the same
time
q)
In case of holding the workpiece by hand, it is
necessary to keep fingers away from the working tip
of the device.
r)
Always use sharp tools.
s)
Always use drills designed to work with a given
material.
Rev. 07.08.2018
t)
Note: Do not touch the drills immediately after using
them. They may be hot and cause skin burns.
u)
It is recommended to wear protective gloves for
replacement of drills in order to avoid burns and cuts
of the skin.
4. Use guidelines
Drill press is a stationary device designed for spot drilling,
drilling holes in various types of materials such as wood,
metal, plywood, etc.
The user is liable for any damage resulting from non-
intended use of the device.
4.1 Device description
2
1
3
4
10
9
8
5
6
7
1.
On / Off switch
2.
Pulley cover
3.
Motor
4.
Lever
5.
Crank fastening the worktop
6.
Column
7.
Basis
8.
Worktop
9.
Jaw chuck
10.
Chuck cover
4.2 Preparing for use
After unpacking the device from the cardboard and
removing the tape, foil and foamed polystyrene it is
necessary to assemble the device according to following
instructions.
List of parts:
A
B
C
D
E
F
3xG
3xJ
H
I
A.
Housing with motor and pulley
B.
Basis
C.
Worktop
D.
Column
Rev. 07.08.2018
E.
Shield
F.
Jaw chuck
G.
Lever handle
H.
Adjustment key
I.
Allen key
J.
Screw with washers
Assembly instructions:
D
C
D
1
B
2
A
A
G
A
D
D
3
4
F
6
7
1.
Screw the column to the base by means of screws
and washers (J).
2.
Slide the worktop onto the column, lock it at the
preferred height by twisting it with the crank.
3.
Loosen the screws located on the side of the housing.
4.
Put the housing with the motor onto the column.
Tighten the bolts loosened earlier and make sure
that the housing is maintained stably on the column.
5.
Screw the lever handles into the threaded holes.
6.
Unscrew the screws.
7.
Install the jaw chuck cover by pressing it. Tighten
the screws. The length of the cover can be adjusted
according to current needs. To this aim, it is necessary
to loosen the wing screws located on the side of the
cover (indicated by the arrow) and extend the cover
to the preferred length (being within the range of the
length of the grooves in the cover). Tighten the wing
screw.
8.
Lift the cover, open the chuck jaws maximally by
means of the adjustment key. Install the jaw chuck
making sure it is free of impurities. In order to mount
the chuck, it is necessary to put it on the spindle, and
then hammer it into place using a piece of wood or
a wooden or rubber mallet. It is forbidden to use
a metal mallet!
The work surface where the device will be located must be
suitable for the size of the appliance, please refer to the
measurements. The work surface must be levelled, dry,
heat-resistant and at a fitting height from the ground to
enable a proper use of the device.
The device can be fixed to the ground by screwing the base
with two screws (in the base there are holes for screws).
5
8
11
Publicité
Table des Matières
