Overhead Rigging; How To Operate The Unit - JB Systems Light Solar LED Mode D'emploi

ENGLISH
DESCRIPTION:
1. DMX input: 3pin male XLR-connector used to
connect universal DMX-cables. This input receives
instructions from a DMX-controller or from another
Solar in master/slave mode.
2. DMX output: 3pin female XLR-connector used to
connect the solar White/RGB with the next unit in
the DMX chain or with another Solar white/RGB
when used in master/slave mode.
3. ¼" jack to connect the optional CA-8 controller.
4. Mains cable
5. Internal microphone
6. Fuse holder

OVERHEAD RIGGING

 Important: The installation must be carried out by
qualified service personal only. Improper installation can result in serious injuries and/or damage
to property. Overhead rigging requires extensive experience! Working load limits should be
respected, certified installation materials should be used, the installed device should be inspected
regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
ELECTRICAL INSTALLATION + ADDRESSING
Important: The electrical installation should be carried out by qualified personal only,
according to the regulations for electrical and mechanical safety in your country.
Electrical installation in DMX-mode:
 The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
"daisy chain" your DMX controller and all the connected units with a good quality balanced cable.
 Both XLR-3pin and XLR-5pin connectors are used, however XLR-3pin is more popular because these
cables are compatible with balanced audio cables.
Pin layout XLR-3pin:
Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+)
Pin layout XLR-5pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+) ~ Pins4+5 not used.
 To prevent strange behavior of the light effects, due to interferences, you must use
a 90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this
simply won't work!
 Make sure that all units are connected to the mains.
 Each light effect in the chain needs to have its proper starting address so it knows
which commands from the controller it has to decode. In the next section you will learn how to set the
DMX addresses.
JB SYSTEMS
®
OPERATION MANUAL
3/36 SOLAR WHITE/RGB
ENGLISH
How to set the DIP-switches to obtain the right starting address:
Each of the first 9 DIP-switches correspond to a certain DMX-value:
DIP #1 #2 #3 #4 #5
Value 1 2 4 8 16
You can combine the values of these switches to become any starting address between 1 and 512:
Begin address = 01  switch 1=ON
Begin address = 05  switch 1+3=ON
Begin address = 09  switch 1+4=ON
Begin address = 13  switch 1+3+4=ON
...
Begin address = 62  switch 2+3+4+5+6=ON

HOW TO OPERATE THE UNIT

1. Standalone 1unit:
Important: The DMX address MUST be set to 001. (first DIP switch = ON, all other are OFF)
Dipswitch 2 has two functions:
OFF: Performs the built-in programs automatically to the rhythm of the music.
ON: Auto mode. Eight Chases (dip switch 3 changes the direction of rotation, dip switch 4,5,6 changes the
speed)
2. Two or more units in master/slave setup:
Connect 2 or more units together using good quality balanced XLR microphone cables. The unit that has no
cable connected to its input will react as master, the others are the slave units.
Important: On the master unit the DMX address MUST be set to 001. (first DIP switch = ON, all other are
OFF) The slave units can have any DMX address value but NOT 001!
You can inverse the behavior of one or more slave units by changing the position of DIP-switch n°10 on
these slaves. Just try it and see if the effect becomes better. Changing DIP-switch n°10 on the master has
no effect.
Notice: when you use Solar White and Solar RGB together in Master/Slave mode, you should set a Solar
RGB unit as Master. If you set a Solar White as Master, the colors of the Solar RGB units will not change
automatically.
3. Connect the optional CA-8 controller for more control:
The CA-8 controller can only be used in standalone or master/slave mode. Connect the controller to the jack
input of the first unit (master). Now you can control all the connected units:
Stand by Blackout the SOLAR WHITE unit (LED ON)
Push for
Function 1. strobe function
2. 2 light strobe
Mode Musical mode (LED OFF)
Stand by Blackout the SOLAR RGB unit (LED ON)
Push for
1. strobe function
Function
2. 2 light strobe
3. Sound strobe
Mode Musical mode (LED OFF)
JB SYSTEMS
®
OPERATION MANUAL
#6 #7 #8 #9 #10
Slave inversion not
32 64 128 256
used in DMX-mode
values: 1
values: 1+4 = 5
values: 1+8 = 9
values: 1+4+8 = 13
values: 2+4+8+16+32 = 62
Rotation & speed selection
automatic mode(LED ON)
Rotation & speed selection
automatic mode(LED ON)
4/36 SOLAR WHITE/RGB