Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
5) SWR ADJUSTMENT
This function allows to adjust the SWR (Standing Wave Ratio) by beep tones.
Press F knob (9) to
enter
MENU.
1.
Turn the rotary CH knob (3) or use the UP/DN buttons (14) on the microphone
to
select
the SWR function.
2.
Press the F knob (9). The radio automatically goes to
pressing PTT switch (13) . The SWR measurement starts. Measurement time
is 5 minutes maximum. The remaining time is displayed.
3.
Adjust your antenna.
4.
The beep tone* is continuous when SWR value is equal to1. 0 . The space
between two beeps became longer when SWR value moves away from1. 0 .
Volume of the beep tone is adjustable with VOLUME knob (1).
Display shows the SWR value. For example 2. 5 .
5.
Press PTT switch (13) to
exit
MENU mode.
*Please check that the beep volume is set to a comfortable listening level.
See § HOW TO ADJUST SWR page 32.
6) EMG SET 1
Allows to
set
the channel and mode for Priority Channel 1.
Press F knob (9) to
enter
MENU.
1.
Turn the rotary CH knob (3) or use UP/DN buttons (14) on the microphone
select
the EMG 1 function.
to
2.
Press F knob (9) to
validate.
The first parameter, channel blinks on LCD.
3.
Turn the rotary CH knob (3) or use UP/DN buttons (14) on the microphone
select
the channel.
to
4.
New press F knob (9) to
validate.
parameter, mode blinks on LCD.
5.
Turn the rotary CH knob (3) or use UP/DN buttons (14) on the microphone
to
select
the mode AM, FM or FM UK (only in U configuration).
6.
New press F knob (9) to validate. The mode stops blinking. a) Go to point
1 to
adjust
another function or b) Press the PTT switch (13) to
exit
MENU.
disappears.
7.
If no key is pressed, the unit
exits
the display.
Default Priority channel 1 is 9/AM.
See § PRIORITY CHANNELS page 34.
7) EMG SET 2
Allows to set the channel, band and mode for Priority Channel 2.
Press F knob (9) to
enter
MENU.
is displayed.
mode without
TX
disappears in the display.
is displayed.
The channel stops blinking. The second
validate
MENU after 10 seconds,
disappears in
is displayed.
1.
Turn the rotary CH knob (3) or use UP/DN buttons (14) on the microphone
to
select
the EMG 2 function.
Points 2 to 7 are identical to § EMG SET 1.
Default Priority channel 2 is 19/AM.
See § PRIORITY CHANNELS page 34.
8) VOX SET
Press F knob (9) to
enter
1.
Turn the rotary CH knob (3) or use UP/DN buttons (14) on the microphone
select
to
the VOX function.
Three adjustments are possible: Sensitivity L / Anti-vox level A / Vox delay time
t (over and over).
2.
Press F knob (9). The current setting (L, A or t) blinks on the LCD.
3.
Turn the rotary CH knob (3) or press the UP/DN (14) keys on the microphone
move
to
to next setting.
4.
Press F knob (9). The value of the current setting blinks on the LCD.
5.
Turn the rotary CH knob (3) or press the UP/DN (14) keys on the microphone
to
adjust
the setting.
6.
Press F knob (9) to
store
7.
Go to point 2 to set both others adjustments of VOX.
8.
Once the settings done, press the PTT switch (13) to
mode. If no adjustment is made for 10 seconds, the unit automatically exits
the function.
-
Sensitivity L: allows the adjustment of the microphone (original one or
optional vox) for an optimum transmission quality. Adjustable level from1
(high level) to 9 (low level).Default value: 5.
Anti-Vox A: allows disabling the transmission generated by the surrounding
-
noise. The level is adjustable. OF (according the squelch level) and from 0
(without anti-vox) to 9 (low level). Default value: OF.
-
Delay time t: allows avoiding the sudden cut of the transmission by adding
and
a delay at the end of speaking. The level is adjustable from 1 (short delay)
to 9 (long delay). Default value; 1.
9) PA SETTING
This function allows to
Press F knob (9) to
enter
1.
Turn the rotary CH knob (3) or use UP/DN buttons (14) on the microphone
to
select
the PASET function.
2.
Press F knob (9) to
validate.
3.
Turn the rotary CH knob (3) or use UP/DN buttons (14) on the microphone
to
select
the operating mode of the PA : I n, OF or PA or.
37
MENU.
is displayed.
and
validate
the setting
exit
the VOX Adjustment
select
the operating mode of Public Address.
MENU.
is displayed.
The current value blinks on LCD.
Publicité
Table des Matières
